DRB GT40 for sale

[TC]

DRB (GT40 Australia)
1966 Ford GT40

Great news for anyone interested in a well sorted out GT40. After some difficult deliberation, I have decided to put my baby up for sale. I currently have another project car in progress and cannot support two dream cars.

This is a stunning red GT40 registered in Florida and built by Colin Dazell. Colin had a very well documented build on his site but I think that was recently pulled down. I will have a copy of the build for any interested buyer.

The mileage is 6,069 and is in beautiful shape. Some major and minor changes, improvements and fine tuning have been done since I purchased this vehicle. See below for some of the descriptions. Price is $72k obo, more pictures will be added, you can email me or call 239-633-6633.

Engine:
Make: Ford / Probe Race 331 Stroker
Stock Displ: 302 c.i.
Current Displ: 331 c.i.
Machining by: Western Motorsports, Inc.
Crank type: 4240 Steel Crank
Connecting rods: TFS Cromo Hardened Pushrods 6.700”
Pistons: Probe forged pistons
Compression Ratio: 10.5:1
Rocker Arms: Comp Pro Magnum Rockers
Harmonic Balancer: Powerbond Race Balancer, 28oz 302/351
Cylinder Heads: TFS High Port Heads
Flywheel Plate: DRB custom for V8/G50
Camshaft: TFS Track Heat Camshaft, 224/232, 557/566
Lifters: Ford racing Hydraulic Roller Lifters
Intake: WMS Victor EFI Intake
Throttle Body: Accufab 4 barrel
Injectors: Ford Racing 30lb Injectors
Horsepower: 425 hp (on dyno after approx 2,500 miles at WMS)
Torque: 400 ftlb
Starter: Kennedy Engineered Products – IMI101
Engine Management: SDS Injection System
Coil: MSD Street Blaster SS – 8207

Transmission:
Make: Porsche
Model: G50/01
Year: 1987

Gearbox rebuilt and hardened by: California Motorsports 928-855-5755

Upgrades and rebuild Info:
pinion shaft 4 point ball bearing
input shaft 4 point ball bearing
differential carrier bearing
differential carrier bearing
1st/2nd synchro ring (steel)----UPGRADE
3rd-5th synchro ring (steel)-----UPGRADE
1 1st/2nd billet steel shift fork----UPGRADE
1 3rd/4th billet steel shift fork ----UPGRADE
1 80% LSD ---------------------------UPGRADE
G50 heavy duty billet alum. side
Cover w/speedo provision----UPGRADE
Cryo/REM process Crown Wheel and Pinion

Custom Gears:
1st gear set G50 2.6154
2nd gear set G50 1.9375
4th gear set G50 0.9667

Brakes:
Master Cylinder: Girling
Bore Size: .625 (rear) / .700 (front)
Reservoirs: Remote 8.3 oz.
Proportioning: Pedal Mounted Bias Adjuster
Front:
Make: Baer
Model: GT Plus
Rotor Diameter: 13” 2-piece drilled and slotted
Caliper: 2 piston PBR calipers
Rear
Type: Baer
Rotor Diameter: 11.5” drilled and slotted
Caliper: 1987 corvette

New brake pads and new CV joints and axle half shafts
Gulf style vent panels on rear deck and rear end

[Simon]

That is a VERY nice looking car! It must be hell to have to part with it.

[Jean-Paul Reckinger]

Hi TC how is the car registrated , as build in what year ?

[TC]

Hey Sabbath,

The car is registered as a 1966 but built in 2004.

[TC]

Hi All,

I need to move this sale along. I can post additional pics or email them to you. I have a excellant covered transporter that I can arrange delivery at $.95/mile. I am also willing to reduce the price to $67,000. This is a good deal. Most of you know that the parts alone usually exceed this price. In fact, on this build the documented materials cost is in excess of $82k.

Also, does anyone have any thoughts on other advertising locations. I have enjoyed this forum so much, I wanted to sell the car here. I found this car here in fact, but it was also on Hemming's and Cobra Country.

[Cliff Beer]

TC, maybe a long shot but perhaps you could give the establishment that is the local Superformance dealer a try for a consignment sale? The local Superformance dealer here in Seattle sells used exotic cars on consignment of all types. Your car looks fantastic, and, being a complete and registered car for a whole lot less $$ than a Superformance roller (sitting right next to it in the showroom) you might just have a quick sale.

[Rick S.]

any interior pics available?

[Jonathan]

Please show some interior pics, also is it gulf flared in the rear? Can you post an angled front photo?

[LoveGT40]

this is a wonderful car.
If I am not wrong 72k us dollars are as 48k euros, a really good price for it.

[TC]

Thanks Cliff, great idea, but a little shy on sending it from FL to the other coast.

Hey Jonathan and rstallare, here are a few photos, I will try to get some better pics in tomorrows daylight. The knob on the dash to the far left is a lean/rich Airfuel control connected to the SDS Engine Management system and the box on the seat is the full and disconnectable systems setting controller.

I have completely redone all of the black trim around the lights and windows and you can see one example of that in the front headlight. The interior door panels have a stitched GT40 emblem in the red panel surround.

Jonathan, not sure if this was an angle you were looking for, if not, just describe it a little more and I will get it tomorrow.

[Paul Butvila]

Very Very nice car! ( If Only...$ )

[Jonathan]

TC,
Thanks for the additional pics. For the front angled shot, can you take another at car level? The car looks amazing.

[Rick S.]

where is the car located?

[TC]

Rick, The car is in Ft Myers, FL.

[craig]

how far is Ft. Myers from the orlando area..
I will be heading to florida 3-22-08 thru 3-29-08 and I would like to take a look..

[craig]

bump..

[craig]

Is this car still 4 sale ....

[Randy V]

Craig - Did you see this in his first post?

you can email me or call 239-633-6633.

[craig]

I just talked with Tony...and the car has been sold.

[TC]

Yup, sorry for any delay in updating this thread. The Gt40 was sold to a very nice gentleman in Wisconsin. Coordinating delivery right now. I think it was a great buy, course I am biased, but also pretty darn aware of all its attributes. The new project car (930) should arrive in a few weeks so the passion still goes on. I have really enjoyed all of the posts on this forum, great bunch of individuals. Be well to all. Tony