GT40s.com
MK-I  MK-II  MK-III  MK-IV  GULF  MIRAGE  J-CAR  LOLA
GT40s.com
Home Forum Gallery Support GT40s.com  
Register FAQ Advertisers Search Today's Posts Mark Forums Read

Go Back   GT40s.com > >

Notices

GT40 Tech - Engines/Induction/Exhaust Motors and engine related - right here!

Reply
 
Thread Tools Display Modes
Old 14th April 2018, 01:43 PM   #21
cscott67's Avatar
cscott67
2 Tenths
United States
 
Join Date: Jul 2003
Location: Daytona
GT40: KVA/RCR
Posts: 273
Thumbs up Re: Bundle of Snakes Advice

I hear you Jac. A good compromise would be a 1.75 bundle to the collectors if Kim is going to thrash it on the track. For the street and shows the stock 1.5 set is probably fine. I don't have any clearance issues like AJ has using the RCR stainless 1.5 set,306, and g50 trans. I'ts possible the engines are installed too high, or not tilted front to back? Dunno. I will post a pick tomorrow. If I remember right my engine is level....... S
__________________
KVA MK1 930 trans/corvette susp./RCR 302/g50
cscott67 is offline   Reply With Quote
Old 14th April 2018, 07:19 PM   #22
70gsconvt
A Tenth
United States
 
Join Date: Jul 2017
Location: Cleveland Ohio
GT40: I wish
Posts: 121
Re: Bundle of Snakes Advice

Great point concerning the angle of the engine. Is the engine/trans supposed to be perfectly level in the chassis, or can it tilt a degree or two down towards the rear for better header clearance? And would that affect the shafts going to the rear tires?
70gsconvt is offline   Reply With Quote
Old 14th April 2018, 08:59 PM   #23
jac mac's Avatar
jac mac
I Have No Life
New Zealand
 
Join Date: Dec 2005
Location: Gore, NZ
Posts: 4,340
Re: Bundle of Snakes Advice

You need to remember 'original' GT40 used small dia flywheel & bellhousing, anything larger compromises that benefit of clearance in horse shoe, also 'original' were mounted off original block mounts, each side of bell housing, two on top of transaxle, therefore 6 places, any change for porsche or other T/Axles is a compromise also, we see many porsche T/Axles mounted off rear housing, they would be better with fabricated mount in axle region that attach to top link of horse shoe along with utilising brackets from lower b/housing to horseshoe on tub. Engine should be mounted as you mention slightly tail down/nose up, not necessarily for header clearance but to ensure coolant in block and heads will tend to self bleed. When you use Audi T/Axles etc with input above axle c/l you destroy that nose high feature and may need bleed lines from rear of intake to help it out.
__________________
AMGT Rep Steel Mono x Plans, FE328 T44R.
[email protected]
jac mac is offline   Reply With Quote
Old 15th April 2018, 12:25 PM   #24
cscott67's Avatar
cscott67
2 Tenths
United States
 
Join Date: Jul 2003
Location: Daytona
GT40: KVA/RCR
Posts: 273
Thumbs up Re: Bundle of Snakes Advice

OP, I went and took pictures today at my shop. The engine IS angled up rear to front. There is at least 4 of clearance between the pipes and rear bonnet fiberglass. I will post pics when I get home and take a measurement of how far the back of the block is from the horse-shoe. S
__________________
KVA MK1 930 trans/corvette susp./RCR 302/g50
cscott67 is offline   Reply With Quote
Old 15th April 2018, 09:07 PM   #25
cscott67's Avatar
cscott67
2 Tenths
United States
 
Join Date: Jul 2003
Location: Daytona
GT40: KVA/RCR
Posts: 273
Thumbs up Re: Bundle of Snakes Advice

Back of block is roughly 4" from front of crossmember. (top of photo is level with chassis) S
Attached Thumbnails
Bundle of Snakes Advice-fullsizeoutput_5a-jpeg  
__________________
KVA MK1 930 trans/corvette susp./RCR 302/g50
cscott67 is offline   Reply With Quote
Old 15th April 2018, 09:13 PM   #26
cscott67's Avatar
cscott67
2 Tenths
United States
 
Join Date: Jul 2003
Location: Daytona
GT40: KVA/RCR
Posts: 273
Thumbs up Re: Bundle of Snakes Advice

Shot under closed clip showing clearance...... S
Attached Thumbnails
Bundle of Snakes Advice-fullsizeoutput_5d-jpeg  
__________________
KVA MK1 930 trans/corvette susp./RCR 302/g50
cscott67 is offline   Reply With Quote
Old Yesterday, 06:53 AM   #27
70gsconvt
A Tenth
United States
 
Join Date: Jul 2017
Location: Cleveland Ohio
GT40: I wish
Posts: 121
Re: Bundle of Snakes Advice

Great reference.
70gsconvt is offline   Reply With Quote
Reply

Tags
exhaust, fit, length, pipe, running


Currently Active Users Viewing This Thread: 2 (1 members and 1 guests)
Crackertoo
Thread Tools
Display Modes

 
Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -4. The time now is 07:27 AM.