Tornado TS40 #875

[Scott Calabro]

Hi Guy's,

Bill,

Thanks so much for the continued compliments.

My 15 inch BRM's have silver spokes with a polished rim, whereas 1027 had black Halibrands. I prefer the BRM wheel though

Tom,

You're welcome!

I wanted to build our Deluxe Component Package to showcase how it really is a GT40 in a box, so mods were not in mind.

Yes this car has been lots of fun to build, all 116 days of it!

I am sure it will be a blast to drive.

My UN1-26 with 3:44 F/D, has no "Mods" either. It will work well with the 385HP 289 that is installed.

To your point on a 200 MPH UN1 equipped GT40, if you were to upgrade one, I don't see why 200 mph is not possible. What you really need for that is an engine capable of turning at or above 6770 rpm in 5th gear.

Assuming a 3:44 F/D, .76 5th gear, and a 26 inch tire.

Also assuming that I didn't make a math error!

The question is, where will you go 200 MPH on the road in Kent

Keep saving Tom and we will put you in a carbon fiber mono GT40!

............................................................ .....................

Today just some spot putty work on the rear clip.

S

[Scott Calabro]

Some progress pics,


Front clip almost done wet sanding and ready for PPG DP 48 white primer sealer.

After that Black down the center of the clip for the stripes, then Begian racing yellow and clear on top!

Next, the rear clip in guide coat.

S

[Bill D]

Scott
I'm really impressed with your progress and all aspects of the kit. This will truly showcase your talents and the Tornado kit.

Back to the wheels...you might consider a second set of BRM's and paint the centers black. I just think that will make your car look super bad!!! Just my $.02

[Scott Calabro]

Thanks Bill!

I had a hard enough time trying to decide on paint, now you have me thinking of black wheels

Yesterday just a little work.

Finished body prep on the front hatch and rear clip.

After a 320 grit wetsand they should be ready to seal and paint.

Spider, doors and sills are next.

S

[EGLITOM]

Great build Scott
will be avery nice car. What does your build time of now app 118 d mean in hours put into the car ?
Thanks
TOM

[Scott Calabro]

Hi Tom,

Why do you ask?

Quite a few, but less than you would think .

The Complete Tornado Deluxe Kits can be built very quickly.

As demonstrated.

The industries only complete self built component GT40 replica.

Thanks,
Scott

[Scott Calabro]

Hi Everybody,

Sorry I have not posted about progress on 875 for a few weeks.

My bodyman has run into some health issues of late and had to have an unforseen operation.

He is not able to complete this job, so I have decided to move 875 to a different shop.

I am pleased to announce I have partnered with Spikes Custom Paint.

They are well known custom paint shop, here in New England.

Very soon a "paint build thread" of 875 will be featured on their website, and of course here too!

They do amazing work!

Check them out here;

spikescustompaint

Cheers,
S

[Scott Calabro]

TS40 #875 arrived at Spike's today.

Here are a few pictures showing the mirrors, rear bulkhead supports, twin pumps & filters and the oil cooler and coolant tank.

Also Spike's shop truck and building.

More to come as the car moves forward.

Cheers,
S

[Andy Green]

Hi Scott,
Looking really good. I presume the oil cooler is only in a temporary position. Otherwise you have effectively blanked a third of it with the bulkhead support and you will get heat-soak from the engine (even though you have wrapped the manifolds). Ideally it wants to be mounted above the battery or the other side, with air ducted in from the side scoop.

Regards

Andy

[Scott Calabro]

Andy,

Pictures can be deceiving sometimes.

Our coolers work well for us in this location/setup.

But thanks for the thought.

Cheers,
Scott

[Andy Green]

Tornado oil coolers may work well in this position, but before the ‘new’ bulkhead support was added.
I was only trying to point you in the right direction so that you have a car that is fit for purpose. It’s your baby.

Regards
Andy

[Scott Calabro]

Hi All,

Just some update pictures from spikescustompaint .

Notice the Green pearl flamed old school fridge, complete with spider web grill

Cheers,
S

[Scott Calabro]

Hi All,

More body update pictures.

Gaps are pretty much completed and the N.A.C.A. duct's are being opened.

The body will probably be disassembled tomorrow for primer coat.

Cheers,
Scott

[Scott Calabro]

Painted the border on both of #875's headlight covers today ...

[Eric Johnson]

Looks good. Keep up the good work Scott...

[Victors]

Scott,

What kind of paint did you use to paint the headlights covers? How did you mask the covers to get such a sharp line?