Search results

My SLC is ready for inspection and I cannot get the windshield wipers to function. The SLC was delivered to me in 2014. I have the infinity wiring system and all other functions work. Any suggestions would be appreciated. Thanks

Looking for a set of hippo mirrors. Lost the lens.

Been working trying to resolve an issue with the Vintage A/C unit is not working. The A/C clutch is not engaging and the Infinity Rear power cell light number 10 is not appearing when power is supplied. I have checked for the Inverter in the wiring for the fans control and it is there. I tried...

What mesh should I used to cover the airbox and the side inlets? Part number and where to purchase would be appreciated. Thanks

Anyone have a heat shield bracket for the Graziano they want to get rid of? I took mine off and can't find it. It's the bracket on the driver's side of the Transaxle. Thanks

In the March Car and Driver there is a good acticle on a Mazda Miata with the LS3 engine. Very tight fit. In looking at the cold air tubes there is only 2 90 degree silicon tubes. Could there be a different throttle body not requiring the 10 inches for the installation of the mast air sensor...

Before I started the SLC, the KOSO unit was working normal. The turn signals, high beams and I could set-up the engine parameter. Since, the start, the KOSO goes through it start-up function then it just shutdowns. I have checking the 12volt and the ground connections and the KOSO is getting...

I am close to starting my SLC and would like to know if there is anything I need to do to prime the fuel system. I have the typical high and low fuel pumps and the swirl tank.

Can you tell me what transaxle fluid I should be using in the Graziano transaxle. I am sure it's been discussed but can't find it. Thanks

Does any one know what the plug dimension behind the alternator for pre-lubing an crate GM LS3 480HP is? I thought it was 14 MM but the socket Allen wrench to take it out is 17 MM. Thanks

Background, I have a GM crate engine and their wiring harness. I when to plug in the MAF sensor and the wiring connector has a different plug. The plug is too big for the sensor. Another quality issues. Has anyone had this issue and if so can you tell me what MAF sensor I should use. These...

Does anyone know the part number for the shift cable retainer clip on the Graziano transaxle? It's must be a small "C" clip. It holds the cable on the transaxle.

On the LS3 passenger side there is a uncapped tube I believe is part of the PCV system. Should his tube be capped, plumbed into the Cold Air tube or plumbed into a oil catch can then into the Cold air tube? Please advise. Getting near to hear noise!! Thanks

Does anyone know of a female connector with the five pins for the Honda S2000 push button start switch? If not, for those who have the button, how did you wire them. Also, can you tell me which pins you used. I believe you would wire the ISIS power to #4 and ground to #5 looking at the back...

For those using a keyless push button starter switch, what switch are you using?

To fit the dash around the rollbar, I cut the corners off the dash. Now there is a big area exposed to the chassis. If I fiberglasss the pieces I cut out in place I won't be able to take the dash out. Looking for suggestion.

Just a heads-up on the bulkhead connectors. I found two wires out of place on the connectors. The pink and tan wires were mis-pinned to the male/female connectors. This would have affected one of the fans and the hydrualic pump.

I am waiting for my fan shroud to be completed and was wondering if a air deflector would help in deflecting the hot air away from the cockpit. I made a deflector out of a piece of scrap sheetmetal that the shroud is being made from. Since my battery is mounted in the front of the vehicle...

I have been looking for a 5000 OHM-1/4 watt resistor to work with the KOSO Dash Meter. I have found 1/4w 5100 ohms resistor and a 1/4 w 4.7K ohms resistor. Can any of these work?

Can someone confirm that for the latest steering column supplied by Fran these are the parts required Quick Release SRK-250-BK (black) and for the short hub SRK-170H. The column is non power, tilt only. Thanks