Recent content by adrian

  1. A

    Winged Dzus fasteners

    All of the fasteners are at the platers now
  2. A

    Winged Dzus fasteners

    Hello Russell Unfortunately without having the dimensions of the Summit Racing fasteners I could not tell you if they are the same. Dzus fasteners come in different widths and lengths. The original one was about 5/8 inch long hence the 60 in the part number back at the beginning of this thread...
  3. A

    Winged Dzus fasteners

    Hello. I have maneged to make 36 as of now but I still need to make another 12 to fulfill wants and for myself so bear with me.
  4. A

    Winged Dzus fasteners

    Hello All A bit more ionformation for you, probably too much but anyway here is a chart of the pigtail receptacles and as you can see there a number of different offsets and sizes. https://www.southco.com/static/JDrawing/j-d4-s6.pdf Even I do not know which are used on my car let alone the...
  5. A

    Winged Dzus fasteners

    Thank you Steve Just need to get the compressor repaired or replaced now.
  6. A

    Winged Dzus fasteners

    The 60 of the EFH6-60 part number refers to the length below the head to one side of the helical slot locked position. If you look on Southco's website and dig quite hard you can find the tech sheets on them. The pdf below should show you specs on the Dzus fastener. It is length L you are...
  7. A

    Winged Dzus fasteners

    Hello John Are you after a set of 4 or do you need more, as I need to send them all off to the zinc platers at the same time as there are minimum charges and I want to get all of them done at the same time. Are you happy with the length of the EHF6 - 60, because I cannot get another length...
  8. A

    Winged Dzus fasteners

    OK...I have managed to make a batch. I have media blasted some of them but the compressor electric motor has burnt out so now I have to wait to get it repaired, but anyway here are some pictures. As soon as I have all of them cleaned up I will get them zinc plated. I have yet to work out how...
  9. A

    Winged Dzus fasteners

    Hello Rod I have had them laser profile cut in mild steel, our English spec for the steel is MS CR4 2 In my experience I have found bronze welding stainless steel to be problematic. Also getting stainless zinc coated or chromed over here is a problem too. So I stayed safe
  10. A

    Winged Dzus fasteners

    Hello Nick I should think those fasteners are original with that part number on them. Southco told me that the part number was dropped a long time ago. It would be a shame to bronze weld over the part number. Some one going for originality might be very interested in them. Adrian
  11. A

    Winged Dzus fasteners

    Hello James Yes I know they are on the short side. My pig tails have been put on the top of the glass fibre of the front clip with a steel pop rivet going through into a washer. I have been down the Mulsanne straight at 180 plus and they are still there. I know if your body material is thick...
  12. A

    Winged Dzus fasteners

    Hello Julian The Dsuz fasteners in the link are not quite correct as the wing on GT40, and the one I have had made, just goes out one side, not both. I will try and post some pictures as long as they do not get lost again. Adrian
  13. A

    Winged Dzus fasteners

    The Dzus fasteners have flat heads and were supplied under the original part number of EHF 6-60 by Southco who supplied the originals. Adrian
  14. A

    Winged Dzus fasteners

    I have had the wings cut now so if anyone wants some pm me. I also bought some original Dzus fatseners from Southco. Obviously I had to buy in bulk so I lots of those too. I will get round to making a set of winged fasteners soon and when I have worked it out I can make some up for people if...
Top