Search results

  1. KENS80V

    GT-R fan shroud help needed.

    I want to pick out a set of fans and build a shroud to use with my future GT-R project. Can someone with a GT-R measure their fan shroud for me please (height and width) It seems most use a pair of 12" fans but that leaves a lot of unused area on the shroud that will block flow at higher...
  2. KENS80V

    Original orange GT40 in Manitoba Canada.

    I enjoyed a conversation with the owner of this original GT40 back in the fall of 2017. He said it was the only one ever painted in orange from the factory.
  3. KENS80V

    27 spline rear stubshafts and C4 Corvette wheel bearings (new) SOLD

    27 spline outer rear stubshafts (pair) for 930 cv joints. $250 shipped SOLD Rear C4 Corvette wheel bearings (pair) with ARP studs. $120 shipped SOLD From the manufacturer.... Front C4 Corvette wheel bearings (pair) with ARP...
  4. KENS80V

    Bellcrank reinforcement plate ideas.

    I'm looking for help in designing bellcrank reinforcement plates. Pictures of what you have designed would be a big help. There have been reports of failure at this joint. My thumb and finger point to the two locations to join.
  5. KENS80V

    Brake line bulkhead fitting source?

    I'm converting my SLC brake system to ABS so I need to have all the brake lines plumbed on the outside (like the newer cars). I can't find a source for the steel bulkhead fittings that convert from 3AN to 3/8" inverted flare for 3/16" brake tubing. I'm pointing to the exact fitting I need.
  6. KENS80V

    FS USA RCR GT40 wiper kit "It's a Snap" (new)

    This is a brand new "It's a Snap" wiper kit that was sold for use in RCR GT40 cars. Price is in US Funds ($150 shipped).
  7. KENS80V

    GT-R bulkhead setback angle.

    Could anybody with a GT-R tell me what angle the bulkhead between the engine and passenger compartment is. I want to make some brackets for a coolant expansion tank and other items to mount to the upper wall. It looks to be approximately 100 degrees from horizontal.
  8. KENS80V

    FS USA C7 Corvette dry sump tank with Aviaid insert

    SOLD This is the factory OEM dry sump tank for the C7 Corvettes. Ideal if you are installing a LT4 engine. This tank was sent to Aviaid to develop a tank insert similar to the C6 Corvette tank. This is their first insert made. The tank was disassembled and meticulously cleaned and then...
  9. KENS80V

    FS USA LS engine heater core bypass valve

    I'm selling my heater core bypass set up for use with LS engines (never used). This is the Old Air Products 50-1555. I converted this control to be used by a toggle on/off switch instead of a rotary switch. Mine can also be used with no switch at all for stealth operation. You would just tap in...
  10. KENS80V

    FS USA Dry sump oil tanks

    Selling my dry sump oil tanks. 1-"new" 2 gallon 12AN bungs attached, single inlet. 19 1/2" tall SOLD 2-"new" 2 1/2 gallon 12AN bungs attached plus 1/2"npt heater port, 2 inlets. 24" tall $380 shipped The 2 gallon and 2 1/2 gallon tanks are brand new and never used. The taller tank has a few...
  11. KENS80V

    FS USA LS3 valley cover reversed with fitting.

    Selling my LS3 valley cover modified for reverse installation. I built a LS9 engine instead. The oil sensor tower was cut off and the surface milled to accept the included LS3 Katech adapter. This adapter is the more expensive one designed for the LS3 intake manifold. It doesn't require any...
  12. KENS80V

    Daniel's S85 build thread

    I hope Daniel doesn't mind me posting a link to his start up video. The sound is just amazing! Did you build all the engine wiring yourself Daniel? Daniel Gherasim - YouTube
  13. KENS80V

    New design Sanden SD7 a/c compressor mount.

    I think I'll try out this Sanden SD7 mount. It seems to be a nice design. It's made from 1/4" thick steel and uses a tensioner for the belt. I like the 4 point stable mount design. LS swap conversion Gen 3- Gen 4 Low Mount A/C Bracket SD7B10
  14. KENS80V

    LS7 exhaust manifold flanges and elbows

    I have collected various LS7 exhaust manifold flanges and elbows. These are original flanges with the recess machined in them. The three sets of flanges are $140 (each set) shipped to you. One set of elbows with the flanges on them. They have the factory O2 bungs on them. Ready to bolt up to...
  15. KENS80V

    WTB- SLC low mount mirrors

    I'm looking to buy a pair of SLC low mount side mirrors. If you received a set with your car purchase and went with something else than I'd be interested in purchasing them from you.
  16. KENS80V

    Olds Intrigue steering column pinouts.

    Here are the pin outs and schematics for the newest style of steering column sold with the SLC and GT-R. I'm not using this column but I thought I'd purchase the factory service manuals and upload these pages to help the RCR community out. I will keep the complete section in the manuals on the...
  17. KENS80V

    Edelbrock LS3 crossram.

    Kinda cool looking but I don't think it will work with the SLC. Maybe the GT-R?
  18. KENS80V

    Racelogic traction control discontuned. was supposed to say discontinued. I was saddened to read today that Racelogic has discontinued their traction control product. I was going to purchase a second unit for my next RCR car. Oh well.
  19. KENS80V

    WTB: SLC dash

    Looking for a SLC dash. I unfortunately cut mine up a bit too much. :stunned: Will pay $250 shipped to Pembina, ND 58271.
  20. KENS80V

    Initial alignment observation help.

    I'm doing some initial alignment adjustments to the front suspension and came across this observation. The drivers side upright sticks out farther than the passenger side by approx. 3/8". If you were to draw an imaginary centerline for the chassis and then measure out to the tub wall where the...