Search results

  1. S

    With deepest sympathy.

    Agree with All of the above he will be sadly missed by all at SGT . RIP Nick.
  2. S

    With deepest sympathy.

    To all his friends . It is with much sadness that I have to report the death of my friend and co worker at SGT Nick Morris he was a devoted gt40 enthusiast and many of you that have met him no he could talk GT 40s all day he was always the first on hand with trolley jack and spanners if...
  3. S

    Distributor that works with TWM/Borla 8-stack

    Hi Henrik the 8579 is 7 1/4" from block face to top of plug lead. Regards Mick.
  4. S

    KVA / SGT build

    Hi Udo make sure it clears the belts. Regards mick.
  5. S

    KVA / SGT build

    Hi Udo I see why you wanted to fit crossmembers and not just bolt the seats to the floor as the SGT seats are completely flat on the base which spreads the load your aftermarket seats would want the ribs across to make them safe and have you decided how the seat belts will be compatible with the...
  6. S

    where to buy a body gt40 at a low price?

    Hi Slava I am away at the moment back at work on Monday have sent you a private message. Regards mick (SGT).
  7. S

    SouthernGT No6

    Well done Nick all your hard work paid off regards mick.
  8. S

    Goodwood Easter Sprint

    Well done Glen and Tammy now you will need a bigger wall to hang them on . Regards Mick
  9. S

    Flywheel fitting ZFQ bellhousing

    Hi Jonas I think there is some confusion over flywheels if you use the Zfq bell housing you will want a 157 teeth flywheel from a v8 our flywheel is smaller it is fitted to sgt cars using original size Zf bell housing you can use our flywheel but would require a different starter motor...
  10. S

    Build sequence, Southern GT

    Hi J the panels are normally fitted first . Regards mick.
  11. S

    SouthernGT No6

    Hi Andy the reason this happened was because there was no room for expansion between the outer diameter of the splined shaft and the alloy upright Both uprights are being machined to correct this and all parts will be checked and re assembled. Regards Mick.
  12. S

    Dreamer From UK

    Hi all just to make it clear the SGT car that had the issues with the cv joints was caused by incorrect length gearbox adaptors being fitted which were not supplied by sgt. Regards mick.
  13. S

    IVA pass today

    Well done Andrew just registration then your off . Regards mick
  14. S

    Oil Leak

    Hi John i have come across 2 different lenghts of input shaft tubes that take the oil seal behind the bellhousing make sure yours is not to short as the seal will not fit tight up against it causing large oil leak. Regards Mick.
  15. S

    So it begins

    Hi Mark you are welcome to visit southerngt anytime just give me a call. Regards Mick.
  16. S

    Size of stacks

    Hi Martin your pulleys and alternator will not fit .The sgt back end will allow you to lower engine and gearbox but will not stop the problems you will have at the front with the set up you have in your picture .The stacks also do look long. Regards mick.
  17. S

    modded chassis on ebay

    Southerngt wish to make it clear that the chassis on this car is not a sgt it was a kva the front end has been built by us and fitted at the factory. The back end was supplied out as a seperate part so any future purchaser should be aware that sgt are not responsible for the correct positioning...
  18. S

    Pulled apart my fuel tank and...WOW

    Hi Bob we run low pressure pumps to the swirl pot then to a filter and hp pump runs faultless . Regards Mick.
  19. S

    John Christian's news

    Hope you get well soon . Best wishes from Mick,Adam,Carol and Stevie.
  20. S

    Southern GT Scores at Goodwood

    Hi Glen well done will make you a reinforced cabinet to put your trophy in. Regards Mick.
Top