Search results

  1. bune

    FORD G.T. Steering Wheel Center Cap Font

    I made mine between two plastic pieces, and the cost was ok.
  2. bune

    get the air out of brakes.

    Funny this. I belive everybody with gt40 must have seen this problem sometime, I have been in gt40 busines for 13 years now, but never observed this. Learn something every day. :)
  3. bune

    get the air out of brakes.

    There are 4 bleed nipples on each caliper, two on top and two in bottom .
  4. bune

    get the air out of brakes.

    Thanks guys. I had a visitor in my garage today , he told me the same, so residual valves(2psi) are ordered from Rally design in Uk. Hope this help.
  5. bune

    get the air out of brakes.

    I filled my brake system with fluid and used a vacum unit to replace the air, but it did not work I replaced and there was no air bubbles.Then I used pressure to push out the air , still it feels like full of air no brake pedal at all. I have Wilwood calipers 4 piston with bleeder on both outer...
  6. bune

    Ball bearing help needed.

    Thanks Paul , since i'm in some hurry, I ordered 4 pieces today , and hope they fit , if not I modifies until they fit . I have to do this job now to be able to complete my other car.
  7. bune

    Ball bearing help needed.

    I belive the name is ball joints
  8. bune

    Ball bearing help needed.

    I have a KVA from 1985-87 and was sold as a kit to two brothers in Sweden. Now 30 years later the car need new ball bearings upper and lower. I have found out that the upright is from a Ford Granada , but The bearings are a secret for me. I have pictures of the 2 parts and hope someone can...
  9. bune

    Assembling a Monocoque

    I am about to do the adjustment on camber and caster, I plan to use 0.5 deg camber front and rear, Have no clue about caster rear, someone out there to help me out with the most common used angles for most street use.
  10. bune

    Assembling a Monocoque

    My car is now back from the painter , and the engine is completed and tested in bench. But still lots of work to do, and now I have to be carefull with the paint.
  11. bune

    Weber 48 IDA setup.

    I do not think that my car ever will go on a track with me in pilot seat and take out all potensial from the engine. I'm to old for that. But I want to know that the engine can be run at max load without any problems, and the diff with the exhaust will not be a issue until someone want to do...
  12. bune

    Weber 48 IDA setup.

    The test stand can load up to 1000hp, (no one can do test with a free spinning engine) . Since this is the first time I do this kind of job, I started with a setup I though was a fair beginning . And I had not a full cabinet with emulsion tubes ,main jet, air corr. etc. I have to think what...
  13. bune

    Weber 48 IDA setup.

    Even if it is a long road to tune the Bolonga Webers I think it is worth it . And now I have the engine in a test bench, it is the ideal condition to tune for max power and in the middle area. The idle can be done home in driveway. I will experiment with the smallest main jets witch not will...
  14. bune

    Weber Tuning Tutorial - On YouTube

    Even if it is a long road to tune the Bolonga Webers I think it is worth it . And now I have the engine in a test bench, it is the ideal condition to tune for max power and in the middle area. The idle can be done home in driveway. I will experiment with the smallest main jets and drill them up...
  15. bune

    Weber 48 IDA setup.

    I use EGT probes and check the spark plugs often , so I feel a bit control. To day I had 435hp in test bench, but over 5000rpm the engine did not get enough fuel, so no I have ordered bigger main fuel jets and air correctors . I feel that I'm close now. Hope to see 450 in bench
  16. bune

    Weber 48 IDA setup.

    I will know more tomorrow after bench test and then I will ask my engine builder for the spec on cam and heads. The main use is street, with a trip on a track few times every year.
  17. bune

    Weber 48 IDA setup.

    I'm struggling with my webers . I started with chokes 42mm main 145 -F7 -air corr 120 idle .70mm this was no good, not able to put any load, run way to lean. Changed the chokes back to the original 37mm and then I had a other engine more promising, will do some load tomorrow . What setup...
  18. bune

    Mechanical Speedo/electronic Transmission

    Where can I get a speedo cable 4 to 10 inches long. I plan to use a mecanichal Smiths gauge later.
  19. bune

    Assembling a Monocoque

    It has been e bad summer ,the body is gone for painting, and the engine is at a test stand. I had to do lot of house related work ordered by my wife . But now the engine have been running for few minutes ,one weber was flooding and the water pump was leaking. Will be fixed monday hopefully. The...
  20. bune

    Balancing wheels with weights

    How do you do the balance job on wide wheels ? The tyre shop put lots off weights on the inside on mine ,it was nice but not practical. I belive that I have to place them visible on the outside, And might have to paint them same as rim. I do not have a good feeling with 270gram on one side of a...
Top