Search results

  1. AllanSLC

    RCR SLC LT4 for sale

    It is no longer for sale.
  2. AllanSLC

    FS USA Race built LS7

    For Sale High Performance LS7 motor built by Walden Automotive. The engine has approximately 3700 miles total with 2600 miles since the build was performed. The build included the following: Clevite rod and main bearings. Engine bored 0.030 over with Weisco 11:1 pistons. Rings were 0.035 over...
  3. AllanSLC

    FS USA Race built LS7

    This engine was pulled out of an SL-C that I am putting an LT5 into. Ferrea Valves Weisco Pistons and rings. Bored 27 over with 30 over rings filed down, the compression is stock at 10.5 :1 Comp dual springs Aviad single stage dry sump pump Clevite bearings It still has the titanium rods The...
  4. AllanSLC

    Suspension cracking sound. Houston builders...

    The shock was making contact with the upper mount and this was easily fixed.
  5. AllanSLC

    Superlite GT-R for sale Sold

    It has been sold.
  6. AllanSLC

    Jokes

    A senior citizen drove his brand new Corvette convertible out of the dealership. Taking off down the road, he floored it to 80 mph, enjoying the wind blowing through what little gray hair he had left. Amazing, he thought as he flew down I-94, pushing the pedal even more. Looking in his rear view...
  7. AllanSLC

    Superlite GT-R for sale Sold

    Yes, it is titled and registered.
  8. AllanSLC

    Superlite GT-R for sale Sold

    Connecticut
  9. AllanSLC

    Superlite GT-R for sale Sold

    Completed Superlite/RCR GT-R Built by Allan LS376/525 hp engine, runs and idles beautifully Graziano trans-axle Drop gears available (not installed) Spec Clutch Mid-rise air intake Canton baffled racing oil pan Coil pack covers Headers, mufflers and cats Infinity Power Box wiring system Raptor...
  10. AllanSLC

    RCR SLC LT4 for sale

    Here's two.
  11. AllanSLC

    Brake Judder!!! What is it? Why does it happen?

    What if any brake residual valves are you using? I've seen where the stock residual valves get stuck causing a vibration like that.
  12. AllanSLC

    A/C will not work

    Locate the master cell input wire for the ac clutch, the one with the inverter. Cut the wire between the inverter and the master cell. With the ignition on, ground that wire that is still connected to the master cell. The circuit for the ac clutch should then come on in the rear power cell...
  13. AllanSLC

    Joel’s SL-C Build Thread

    Looks great. Do you know what system you'll be using for the power brakes?
  14. AllanSLC

    Insurance Question

    https://www.midwestclassicinsurance.com/cobras-kits
  15. AllanSLC

    Michael's GT-R Build

    Top row in pic, mounts for parking brake handle. Used for SL-C on interior center rail. Next row, front engine mounts, slide on frame between were the engine mount sits on frame. Parking brake mount. Gated shifter mount. Tabs that bend down are for SL-C, but you can remove them and use for...
  16. AllanSLC

    Infinity interface for Autoloc controls for power doors.

    I spoke with Jay at Infinity and he is in the process of developing 2 negative outputs from the mastercell that will activate each of the motor controllers already in the car.
  17. AllanSLC

    Wiring fans to both come on for AC or Engine

    You're welcome
  18. AllanSLC

    Weird LS startup issue - fuel or electrical?

    Have you opened up the Fitech surge tank? I had one where the tube that goes from the pump in there to the outlet broke. It would then only supply 20 psi. What is the output of your alternator? Is it more than 50 amps?
  19. AllanSLC

    SLC picture thread

    1500 hp, 1305 rwhp twin turbo
  20. AllanSLC

    Wiring fans to both come on for AC or Engine

    Take the 2 output power wires for the fans in the Infinity Box and splice them together. Run 2 output wires from the splice. 1 wire to the trigger wire on a 30 amp relay and the other wire to the trigger wire on another 30 amp relay. Run an in line fused power wire from the battery (or mega...
Top