Search results

  1. L

    Original P1015 Dash Switch

    Thank you all for the replies and schematic. Now I know it's a dimmer. Louis
  2. L

    Original P1015 Dash Switch

    Hi All, This attached picture of the original dash in the P1015 has a switch between the toggle switches. Does anyone know what this switch does? Thank you! Louis RCR GT40 MKII
  3. L

    Louis' RCR MKII Build

    Hi Morten! Good to hear from you. The RCR specs for caster are 5-8 degrees. Mine was set to 6deg. The solution will come. Louis
  4. L

    Louis' RCR MKII Build

    Advice from Bill at RCR was to double-check my suspension alignment before cutting anymore on the rocker panels. Always wanted to make aluminum spacers to replace the shim washers anyway so I'm doing that. Before I took the suspension back down the wheelbase = 94.5" Close to 95 specified by...
  5. L

    Louis' RCR MKII Build

    Hi Adam, If I remember correctly: End of right rear rocker to chassis: ~45mm or more End of left rear rocker to chassis: ~47mm (honestly can't remember) From your thread they should be 52 - 54 mm. So the rockers on my car need to move back toward the rear tire.. Thanks! Louis
  6. L

    Louis' RCR MKII Build

    Rockers Hi All, Another rocker question for the group. The tires are hitting the rockers even though the rockers as far back as possible and the front suspension as far forward as possible. I've trimmed a little here and there hoping to get them to go back. I've seen some cut the front...
  7. L

    Alan's RCR40

    Very nice Alan! I will check my tanks with a light too to make sure I see no holes in the tanks. Louis
  8. L

    Louis' RCR MKII Build

    Hi Gale, The rockers you see in the pictures are in the correct orientation. Thank you! Louis
  9. L

    Louis' RCR MKII Build

    Hi Gale! I never thought of that but now that I really look at it .... The rockers came bolted on the way you see them in the pictures. I'll take a closer look at them tonight. If they are backwards I'll just have to laugh some more. Louis
  10. L

    Louis' RCR MKII Build

    I appreciate everyone's input into my issues. In talking with Alan I have a much clearer understanding of what's going on with my car. Also must thank Alan for his description of what's it's like to drive a finished GT40. Even over the phone I could feel the adrenaline in his voice. Thanks...
  11. L

    Louis' RCR MKII Build

    Hi Alan, The lip of the spyder is just over 1/4" from the spare tire well. See attached. Thanks! Louis
  12. L

    Louis' RCR MKII Build

    I missed a few pictures. Louis
  13. L

    Louis' RCR MKII Build

    Hi All, I believe it Ron. The spyder can definitely go back more. There is clearance for the spyder to go another 3/4" before it contacts the roll bar. I've attached a few pictures. Not the best picture but the spyder lip is definitely too close to the spare tire well. Since this car was...
  14. L

    Louis' RCR MKII Build

    Hi Walt, Guess I could do that. I'm sure that would be a last resort but if that's what it takes then trimming I will do. Thank you! Louis
  15. L

    Louis' RCR MKII Build

    Allen, Pretty sure it sits back but will double check at lunch. Thank you! Louis
  16. L

    Louis' RCR MKII Build

    Wheel Centering in Front Clip When I mounted the front clip the aesthetics of the wheel not being centered in the arch is not good. So I took all the washers out, except for the heim bearing washers, so I could move the top and lower arms as much as possible while checking for proper caster...
  17. L

    Louis' RCR MKII Build

    Hi All, It's been awhile and I apologize for not posting pictures. Honestly, I haven't been able to accomplish much on the car over the past year. I did install the AC system as per Rick's installation. That was a nice clean install. After next week I should be able to spend more time at...
  18. L

    Hi Rick! Can you call or send me a txt message? Had to get a new phone and your contact info...

    Hi Rick! Can you call or send me a txt message? Had to get a new phone and your contact info did not transfer over to the my new phone. I need info on the rear suspension washer location(s). I still have the note you gave me on how many washers forward/rearward but not sure where on the rear...
  19. L

    Mating an O1E Transaxle with a 302SBF

    That 351W is tall! Appreciate this Morten! Louis
  20. L

    Mating an O1E Transaxle with a 302SBF

    Appreciate it very much Morten! Louis
Top