Search results

  1. A

    Fling SLC Build Thread

    It's by far my favorite SL-C so far, I must share your taste in body customizations.
  2. A

    Kurt H (hoffkm) SL-C build thread

    I have you looked at these new relays? Pretty slick: https://www.kaizenspeed.com/products/kaizen-relay
  3. A

    Restarting my SLC project in West Texas

    I made the same mistake. Better to extend the harness than heat up the cabin in Houston
  4. A

    Scratch Build of Jag XJ220 Replica

    This is my new favorite thread. Always wanted to take a stab at this car one day.
  5. A

    Fling SLC Build Thread

    Those headlights are such a huge improvement. Looking really good, you must be excited to finish it.
  6. A

    Centroid Fuel Sender

    I don't know who makes it for them, but I've been running one in my mustang with no problems. Funny thing is they don't seem to sell it anymore, I can't find it on their website.
  7. A

    Centroid Fuel Sender

    You can order one from speedhut and they will custom cut it to any length you want.
  8. A

    Centroid Fuel Sender

    I have one that looks identical that I got from speedhut, no issues at all with it.
  9. A

    H Craft GT-R, Jared's build.

    I count 6
  10. A

    Restarting my SLC project in West Texas

    I did notice when I was doing my initial charge a few weeks ago that if the blower was set on a very low speed (it's a VFD) the air temp would drop down to around 26 degrees. If I turned the blower up towards medium it would raise up to about 39 degrees.
  11. A

    Restarting my SLC project in West Texas

    You should be able to accomplish the same thing by adjusting the heater valve (or adding a small bypass) to never be all the way off, always leave a little hot water flowing through the coils.
  12. A

    Restarting my SLC project in West Texas

    Heater hoses are usually a #10AN fitting with a 5/8 barb for the hose. The AC will be a #10 O-Ring AN and a #6 O-Ring AN.
  13. A

    Restarting my SLC project in West Texas

    rock auto has the best price if you buy in boxes of ten.
  14. A

    Michael's GT-R Build

    Looking really good
  15. A

    Restarting my SLC project in West Texas

    I’m using these on my current build, and boy does it get expensive if you have to start cutting these for troubleshooting. Make sure you are happy with everything before you put the heat on these bad boys.
  16. A

    Restarting my SLC project in West Texas

    Anywhere I can't use a the stepless clamps I use a T-bolt clamp. I'm so tired of cutting myself on a worm clamp.
  17. A

    Mason’s Build: Superlite SLC

    I have no practical experience from trying to hookup a heater core that way, but a few fluid flow classes from college lead me to believe that you will get very little circulation through the core by tapping the 1.5” lines, regardless of what angle you use. The issue is that the 1.5” line dumps...
  18. A

    Mason’s Build: Superlite SLC

    I've never really found any aftermarket connector I was really happy with, at least not a price I was willing to pay. I tend to hit the junkyard and find OEM connectors that use the delphi style pins so that I de-pin them and put in new pins from cheap amazon weatherpack connectors. I have...
  19. A

    Restarting my SLC project in West Texas

    If you already have hoses, then the cost will be far too high, I didn't realize those were already in the kit. I did not have hoses, and the cost of the EZ Clip system was about the same as a standard system + buying a crimper (so EZ Clip was about $250 more). You can find the stuff...
Top