Search results

  1. Dan carter

    Cadillac Alternator Jumper Wire? - Need Electrical Insight

    I'm using the 2004-2007 Cadillac alternator 150AMP (GM 84009383). I'm having an issue (electrical is not my strength), but the volt meter in the cockpit will at time show a strong 14 volts then fall to about 12.5 volts and then migrate back up to about 13.5 or so (as best I can read the volt...
  2. Dan carter

    Centroid Fuel Sender

    Most of us probably have the original Centroid fuel level sender in the tank. I believe the unit we have has continuous output of 2.33V empty and 0.54V full. My fuel gauge is based on ohms (240 empty and 33 full). 240/33 is the factory default setting from Speedhut for the fuel gauge (it is...
  3. Dan carter

    Toe String Alignment Ref Points

    Gents Without the body on, there are a lot of reference points to complete a string alignment for toe. Just looking to see what anyone is using to square up the reference lines once the body is on.....aka what reference point are you using to square things up?
  4. Dan carter

    RAMLIFTPRO Repair

    I have a puck that is leaking. Cant find anything on the web on repairing the leaks. I have the repair kit, but cant get it apart. Anyone ever disassembled the ram? It has 3 rings, center ring extends with air/hydraulics. Inner ring has two holes suggesting it may thread from the outer...
  5. Dan carter

    To tune or not to tune....that is the question

    This subject may be too involved for the forum, but I thought it might be a good idea to share some knowledge about the tuning process, so I have put this together to get a dialogue started. It may go nowhere, or we may learn a lot from the more experienced among us. I’ve chose like so many, the...
  6. Dan carter

    Graz & Shift Adjustment

    1. Is there a best/correct way to adjust the original shifter and the Graz tranny? I see there is an alignment hole at the tranny linkage but not certain the best way to use it, if at all, with the stock shifter? 2. I can only get back into first gear after I stop the car (aka it won't...
  7. Dan carter

    LS3/480 Tune

    If anyone has an LS3/480 tune they think is really good, if your willing and able I would like to compare it to the one I have. I have the HP tuner tools and software and would appreciate anyone sharing if willing. I'm having a random stall issue that's new, but not sure where its at. Thanks
  8. Dan carter

    Looking for STOCK throttle table for LS3/480

    Gents, tried the net but no luck. If anyone took a snap shot or captured the GM stock throttle table in the engine controller, would mind sharing it with me. It’s a long story, but seeing it will give me confirmation on an issue I’m experiencing with the controller. Thanks
  9. Dan carter

    Dreaded P0606 Code

    I haven't seen this one discussed so I just experienced a PO606 error code. IAW the internet it could be all kinds of stuff. Before I dig in, has anyone had this code and what did you do? Thanks
  10. Dan carter

    Stronger Starter

    The stock starter for the Graz is the Bosch SR0408X. Its a refurbished unit built for Volkswagens from 1995 - 2006 for nothing more than a 1.9L engine. Has anyone found a stronger gear reduction unit or anything better than this unit?
  11. Dan carter

    SLC Car Cover

    OK, this is an odd question, but has anyone found a ready made car cover that fits over the SLC? I have a wing which is making it harder than usual. I have a couple oif car shows to attend and the cover will come in handy.
  12. Dan carter

    Standard shifter - internally adjustable?

    I know many of us are less than pleased with the standard shifter, but has anyone ever played with adjusting the internal parts? Looks like there is some opportunity to adjust its movement as it exits.
  13. Dan carter

    Tuner List - Share your Recommendation

    Gents After 4 tuners, it has dawned on me (a little slow I guess) that tuners are every bit as critical to our projects as hardware. I wanted to start this thread to share with all builders the good tuners we have found (so list yours as well). Tuners are typically local, unless they travel or...
  14. Dan carter

    Need Verification on Fuel Tank Threads

    Gents I discovered a leak at the fitting that feeds the fuel pump from the tank (the bottom one on the tank). What type of thread did RCR use on the tank, I don't see it in my notes anywhere? I'm hoping I used the right type of adapter thread into the tank. Thanks
  15. Dan carter

    Best way to adjust Grazianno shift cables?

    I have a whopping 40 miles on the car. I’m struggling with getting into first and second on a downshift. Up shifts are fine. I have the old shifter so when I set my cables on the shifter arms of the Graz, I set the shifter in as neutral a position as it would allow and the transmission in...
  16. Dan carter

    Flowmaster DBX mufflers

    Can’t find who used the FLow Master DBX round mufflers, but if you did, what is your opinion, quiet, loud etc. I’m using Magnaflow and not impressed.
  17. Dan carter

    Weather seal, mounted on door or body

    Got a question. I set my doors to be as flush to the mating body panels as I could get them anticipating the need for weather stripping. I purchased the type from McMaster Carr that has been suggested on the forum. In mounting the seal, I would have preferred to mount to the door versus the...
  18. Dan carter

    Request a cross check on heater plumbing

    Guys Before I tear into the heater plumbing, take a look at my schematic. I can measure 140 degree heat on the engine side of the 4 way valve but on 60 on the heater side. I see the motor on the diverter valve move when I turn the switch, but it still stays cold on the heater side of the...
  19. Dan carter

    Mazda Door Locks - I'm stuck

    Gents Looking for some help/thoughts on the Mazda door locks. I copied the solution suggested to design a door locking capability from the forum. However I have run into a concern. The "Z" bracket attached to top of the tumbler had to be straightened (now an L shape) to stop hitting the...
  20. Dan carter

    Front wheel main body protection

    Just pulsing the blog to see what others may have done to protect the main body area that is exposed to debris from the front wheel. By chance has anyone tried the tintable RAPTOR sprayable bed liner. Curious how it accepted color.
Top