Search results

  1. C

    rear clip and rims for sale

    (and if possible weight of the wheels, should be light for that size in magnesium)
  2. C

    rear clip and rims for sale

    No rush. Most likely 14" wide and six pin drive.......
  3. C

    rear clip and rims for sale

    OP, What is/are the width of the rear wheels and offset? (from rear mounting flange to outer lip of wheels) Six pin drive or five pin, and pin hole spacing?? Thanks, Scott
  4. C

    What might you do?

    As already mentioned the cost of an SPF roller is roughly 2.5x what a deluxe RCR kit runs. By the time you get the RCR to the same level of fit/finish completion they are much closer in cost depending on WHO is doing the work. If you plan on doing any serious track time with the gt40 I would...
  5. C

    Rear Vent Measurement

    Panel is 18x12.....
  6. C

    Tires for 15”x14” rim??

    Takis, I would stay away from the MT Sportsmans for a road car. I bought a set when I first,"Gulfed" the rear clip for set-up and rim/tire sizing. They looked like AVONs, were out of round, and would have had to have been shaved. Even then I probably would have never gotten rid of all the...
  7. C

    Tires for 15”x14” rim??

    Here is a pic........during a quick alignment.
  8. C

    Tires for 15”x14” rim??

    M&H makes a 390 45/15 drag radial that is dot certified......... (it is a little taller like 33, I run it on my RCR GT40)
  9. C

    Avon CR6ZZ. age of tire

    Fred, general rule of thumb is replace at 5 years.There is supposed to be another set of numbers stating when tire was made......ex 2010 would mean 20thwk of 2010. S
  10. C

    Busy weekend

    They look about right to me! ;0)
  11. C

    Looking for an affordable body. No longer looking

    OP, Best bet is to call/email Bill or Fran. Chris Arden may have something for you right now. (get all the parts from one source) Trying to marry different parts together is a real job if you are not a professional fiberglass repair guy as mentioned in a previous thread. Scott
  12. C

    Doors

    OP, Randy, You wont be able to fit the front or rear clips easily either as they wont match up between replicas!! A HOT MESS to say the least....... I would recc. you buy the body all together from one source. (unless of course you or a GOOD friend are great at repairing fiberglass/corvette/boat...
  13. C

    dropped floor tray

    JP, You may want to try putting the back of your seat all the way up against the bulkhead. I dont have a picture of my seat handy, but it hinges in the middle where the top and bottom half meet so you can adjust the slope. I am 6'2" and lay back in my seat and clear with about an inch to spare...
  14. C

    steering wheels and misc

    OP, sent you a PM. Scott
  15. C

    427 side oiler in KVA

    Porsche 930 trans or Rbt........
  16. C

    Tire pressure for NT555?

    Dwight, I run about 25-26psi on all four corners while on the street with DRs. (you can mark a couple of lines across the tire treads and check the wear pattern after a short drive) . Adjust as necc. S
  17. C

    Hello from Florida

    Welcome Danny and George! A friend of mine in Lake Helen has an up and running Active Power chassis. I am in Daytona beach-side. Where are you located Danny? Congrats to you both, S
  18. C

    Happy 4th July

    More humor for the 4th!! S
  19. C

    What's better than two GT40s in Colorado?

    Tom, Was nice to see you again and see all the mods to your 40! Hopefully next time we can get them on the track and wring them out a little...... Mike thanks for the pics/video and bringing your SPF out. Was nice to meet you and hope you decide to keep your car. Now lets plan a trip to...
  20. C

    Rumor Has It . . .

    OP, The Superformance wide body rear clip looks a LOT different than the wide body gulf cars I checked out a couple of years ago at the Amelia Island Concours. (the rear clips looked more like flairs were added to standard width bodies, rather than widening the rear deck and changing the flair...
Top