Search results

  1. RexDanni

    Ryans Group Ten GT40 build - Body 5.

    I also think that it looks out a bit. As soon as I have scanned my MK IV body, I can see in the CAD how it will look like on my car Whereby the high positioned drive shafts are very good. With it you can get almost straight to the wheel
  2. RexDanni

    Ryans Group Ten GT40 build - Body 5.

    Here is the difference between O1E and Audi R8 Graziano gearbox. The drive shaft of the Graziano is about 124 mm higher but the gearbox is also about 84 mm longer.
  3. RexDanni

    Ryans Group Ten GT40 build - Body 5.

    Hello, Ryan, yesterday I got the data from the engine and a Graziano gearbox. The transmission looks much better! The guys there are really good. Thanks for the hint to the construction planes, I almost overlooked that. It is a bit tricky to use them in my CAD, but it worked. It makes it much...
  4. RexDanni

    Ryans Group Ten GT40 build - Body 5.

    Hello, Ryan, Thanks for the great tip to the Bremar website, now I have reasonable scan data ! Thanks !!
  5. RexDanni

    MK IV tubular spaceframe drawing

    Hi , I have now completely redesigned my frame. Additionally I have done extensive FEM studies. I have always used 42crmo4 with 800-1000Nm tensile strength as material. The tubes are 40x40x2 and 25x25x2 mm Unfortunately I have to realize that there are only round tubes made of this material :(...
  6. Stand_29_04_36.JPG

    Stand_29_04_36.JPG

  7. Stand_29_04_38.JPG

    Stand_29_04_38.JPG

  8. Stand_29_04_37.JPG

    Stand_29_04_37.JPG

  9. Stand_29_04_40.JPG

    Stand_29_04_40.JPG

  10. Stand_29_04_44.JPG

    Stand_29_04_44.JPG

  11. Stand_29_04_39.JPG

    Stand_29_04_39.JPG

  12. Stand_29_04_43.JPG

    Stand_29_04_43.JPG

  13. MK IV from Scratch

    MK IV from Scratch

    CAD work
  14. Stand_29_04_41.JPG

    Stand_29_04_41.JPG

  15. Stand_29_04_42.JPG

    Stand_29_04_42.JPG

  16. RexDanni

    Hi, Dusty, I plan the same configuration for my project. Dartblock engine with 5,4 ltr. and...

    Hi, Dusty, I plan the same configuration for my project. Dartblock engine with 5,4 ltr. and Graziano gearbox. Could you explain to me what you use to connect the two? That would be very helpful for me. I don't have a plan at the moment, which adapter plate, clutch etc. cheers Hans
  17. RexDanni

    Hacking an IDA 'Weber', turning it into EFI

    "....I'll probably have to draw a sketch to figure out what angle would work for me." This is certainly a very good idea! By the way, there are also retrofit systems for weber carbs. Here only the throttle valve is used - everything else flies out. The injector sits in the middle, where...
  18. RexDanni

    Hacking an IDA 'Weber', turning it into EFI

    One must also pay attention to the injection angle of the injector. These are not only straight but also with predefined angles. At Bosch, for example, the range is -10° / -5° / 0° / +5° / +10°. (As far as I know) Here is an example how I designed this for an Audi V10 engine. The injectors...
  19. RexDanni

    Which engine for my MK IV project?

    Thanks Andy, I have sent him an email..
Top