Search results

  1. Shaun Sizen

    May the Fourth....

    Not sure about Jedi but a bloody good machinist that's for sure!!
  2. Shaun Sizen

    Renault UN1 output shaft issue

    So LSD or not? Divorce or peaceful marriage :)
  3. Shaun Sizen

    Renault UN1 output shaft issue

    Probably is it was an old post!!
  4. Shaun Sizen

    Renault UN1 output shaft issue

    Ouch.....I have a LSD on mine but cannot comment as its still very much in build as you know. Sure there will be comment on here, as you say good time to do it but they are not cheap, still no foreign holidays for a while so treat yourself!! I did read on the web someone made a tool using an...
  5. Shaun Sizen

    Southern GT Chassis #54 Build - The What Have I Done Chronicles!!

    Be careful we may get into what is a good and bad roll bar!!! 4x2 probably not race safe but a great idea for the roof thanks. Mine is I think pretty flat hence Mick spotting it, thing is the front fibreglass lip seems to be as far back against the chassis box section as it can go? I will have a...
  6. Shaun Sizen

    Southern GT Chassis #54 Build - The What Have I Done Chronicles!!

    Thanks all, Mick thinks as well my spider is too far forward making the roof too low, need to push it back to raise the roof Randy I like the idea of the support that would help, carpentry time!!
  7. Shaun Sizen

    Southern GT Chassis #54 Build - The What Have I Done Chronicles!!

    I like the bonnet adjuster idea, going to fit the latches tonight see what that does, cheers
  8. Shaun Sizen

    Southern GT Chassis #54 Build - The What Have I Done Chronicles!!

    Paul a damned good point!!!! There I was pondering last night not being able to sleep and I did wonder if there was another clip to hold that down like the rear How about your cills did you have to chop and add or remove?
  9. Shaun Sizen

    Southern GT Chassis #54 Build - The What Have I Done Chronicles!!

    Body body body....So took the plunge and started on the body fit, so far and early days its not too bad, the rear clam is not a million miles away, some grinding round the top lip and had to oval the holes in the spider just to pull them out a little to fit the profiles as below Alternate use...
  10. Shaun Sizen

    Renault UN1 output shaft issue

    Hi Paul, mine have nowhere near that amount of play even when the oil O rings were missing, as andy says its best get that sorted it won't go away Cheers
  11. Shaun Sizen

    Redline Linkage kit for IDF

    That's the one, cheers all, mind you not cheap but I guess all 40 stuff is not cheap but what is :) :) :)
  12. Shaun Sizen

    Redline Linkage kit for IDF

    Not wanting to hijack this thread but I am looking kist for this part or one similar mine is pants quality....
  13. Shaun Sizen

    Southern GT Chassis #54 Build - The What Have I Done Chronicles!!

    Cheers Andy just heard back from Chris and yes its not correct so have to drain the box and send back to Chris to take a look, at least the whole box does not have to come out like last tine when the oil seals were missing. Thanks for checking yours really appreciated.
  14. Shaun Sizen

    Southern GT Chassis #54 Build - The What Have I Done Chronicles!!

    This is a link to a video of the play, about 1mm in either direction, is that excessive? There is an oil seal in there just wonder if its the right one? https://photos.app.goo.gl/ntu7tNmieWuvTEDB6
  15. Shaun Sizen

    Southern GT Chassis #54 Build - The What Have I Done Chronicles!!

    Cheers Andy, mine was fully rebuilt by Chris Cole but the oil seals were forgotten just hoping nothing is forgotten here as well will drain and take a look, cheers
  16. Shaun Sizen

    Southern GT Chassis #54 Build - The What Have I Done Chronicles!!

    Been too long since an update, where is the time going these days? Has Covid changed the spin of the earth, April whizzing by before we know it it will be the longest day. Not so much progress, finally finished a pool hut I started in the first lockdown, only took a year!!! Busmans holiday i...
  17. Shaun Sizen

    Southern GT #28

    Hi Hamish If its drill for rivets I used the Milwaukee Hex Shank bits in packs of 2 they eat steel I did get a set of Milwaukee HSS drills but they were pretty rank, just caught the whole time and spun in the chuck, not as bad mind as the DeWalt ones they were true shockers. Also the best...
  18. Shaun Sizen

    Upper Trailing Arm Cut-Outs

    Quite a chunk it seems, Simon also sent a photo over of Micks car so out came the angle grinder and off bits came!!
  19. Shaun Sizen

    Upper Trailing Arm Cut-Outs

    Evening all How much did anyone have to remove from the rear clam to clear the upper trailing arms? SGT kit but I guess all the same, Alex Veys sent me an image and looks like he chopped a fair bit out, just wondered why the shell was made like that unless its for any chassis' that don't have...
  20. Shaun Sizen

    Chuck's Jaguar D Type Build

    Great build log and has tempted we away for my next build for the standard Cobra (well I may take the GD kit anyway as I have a slot) and direct to a D Type, I will endeavour to catch up but do need to get the 40 done first, oh busy days ahead!!
Top