Search results

  1. mksetter

    Hella Headlight Connector Help

    Thanks for your help. The order is in.
  2. mksetter

    Mark's GT-R Build

    Mounting the Fog Lights is a little more complicated than the head lights. The head lights have a trim piece to cover the mounting screws. The Fog Light buckets have no trim cover. I did not want the screws to show, so I used some plastic boards. The Fog Lights needed to be set back an inch...
  3. mksetter

    Mark's GT-R Build

    I will be painting the inside of the headlight buckets silver, matching the strips color. The headlight are in position, but still need spacers to get their depth correct.
  4. mksetter

    Mark's GT-R Build

    Used some plaster to make the mold to extend a few areas. After roughing up the areas needing additional material, I added the fiberglass. Selective spot trimming and finally got a reasonably fit. This is the before.
  5. mksetter

    Mark's GT-R Build

    The body is the next step. Headlight frames need some fitting.
  6. mksetter

    Mark's GT-R Build

    I have the wiring almost complete, and went through testing each circuit. Most of them tested great, until I got to the circuit involving the Summit Raptor Pro. As soon as I put power to that system, the right turn signal started blinking not having tough any buttons. Pushing the right turn...
  7. mksetter

    Hella Headlight Connector Help

    I am ready to make the wiring harness for the headlight of my GT-R, but don't know the connector that I need. Does anyone know the part number and where to order the connector for the Hella headlights?
  8. mksetter

    Problem with the Summit Raptor Pro

    When I started to work on the sound system, Scott Rowland, who is very knowledgeable on many thing, but especially on audio, talked about speaker position and he suggested avoiding the doors and using kick spaces, if they are available. That have a more stable, solid surface to mount on and you...
  9. mksetter

    Problem with the Summit Raptor Pro

    Don't all cars have a hamster track? Allan, thanks for the contact. I will get in contact with them.
  10. mksetter

    Problem with the Summit Raptor Pro

    I am getting close to having the wiring complete and was checking each circuit and hit the wall with the turn signals and driving lights. Everyone says to check all of the connections, then re-check the grounds. All of my connections are crimped, soldered and waterproofed with heat shrink...
  11. mksetter

    Mark's GT-R Build

    The relays and circuit breaker here may look familiar to most of you. This is my circuit board for the Vintage Air System. After looking at some YouTube videos on installing this system and hearing the pros and cons of reducing the wiring that was provided by Vintage Air, I decided that the...
  12. mksetter

    Mark's GT-R Build

    I just received the rear clam hinges I asked H to make for me. Again, the master delivered. The cross brace for re-enforcing the clam is curved to fit the inside of the rear clam perfectly and I know the hinges will work. Thanks H.
  13. mksetter

    Mark's GT-R Build

    I am doing the final steps in wiring and will be testing all of the circuits next week. I also had to work on the clutch master cylinder. The size of the master cylinders that came with the kit included two smaller sizes for the front brakes and the clutch, and a larger one for the rear...
  14. mksetter

    Mark's GT-R Build

    Still working on the wiring, getting closer to having it finished. This is the switch panel I will be using in the overhead console. Watson Streetworks made the switches. Really nice stuff. Ignition On, Headlights/Running Lights, Fog Lights and Interior Light, all with indicator lamps. I...
  15. mksetter

    Mark's GT-R Build

    The members of this forum have helped me again. Luke S suggested I consider adding billet louvers to the rear clam to add to the look already started with the carbon fiber intake and valve covers. I never really considered it until he mentioned it. He was absolutely right. They look great...
  16. mksetter

    Ken's SLC build thread

    Wow Ken! Your fabrication is off the meter! I have learned so much from your build. Thanks for sharing.
  17. mksetter

    H Craft GT-R

    If I could add a superlative greater than those already stated, I would, but every one of these comments is true. Your car is unbelievable! Thanks for showing us what “The Best” looks like.
  18. mksetter

    Mark's GT-R Build

    This is the dash gauge set final wired and organized. I want the final install of every component to be as easy and least likely to get scratched as possible, so these wires needed to be wrapped.
  19. mksetter

    Mark's GT-R Build

    The wiring is almost complete. This one relay board is just used to control the running lights, turn signals and four way flashers, so that the running lights will shut off it either that side turn signal is used or of the four way flasher is used. This look a little messy now, but it will be...
  20. mksetter

    I think I have one that I did not need to use because a friend with tons of experience helped me...

    I think I have one that I did not need to use because a friend with tons of experience helped me align mine. I will be in my shop tomorrow and will let you know. You can have it if I have one. Mark
Top