Search results

  1. D

    10E AEK-Z 6 GETRAG - Can anyone identify the port under this goopy mess?

    Hello Everyone. This is a photo of the right side (looking from the rear) of a 10E rebuilt transmission purchased from Advanced Automotion. I asked Scott about this goopy mess and he told me not to mess around with this otherwise it may cause $800.00 in damage. I used to overhaul Chevy 350...
  2. D

    Rear lower wishbone dimension (for mock up)

    Good morning. I have searched around looking for Forte' spaceframe rear lower wishbone tubular dimensions un-successfully. Would anyone happen to know where I can find these dimensions? I would like to mock one up our of PVC in order to get an idea of the positioning of my rear uprights. I...
  3. D

    New GT40 build - GT40 Forte'

    Yes Sir. I will be flipping that brace soon : o)
  4. D

    Ford Sierra Hub and Bearing for 100mm final flange

    Hello All. I am attempting to source a set of Ford Sierra/Cosworth hub carriers and proper size bearings for my CV drive shafts. These are the shafts I have... FORD SIERRA-WESTFIELD DRIVESHAFT SET & STUB AXLE (100mm) https://www.ebay.com/itm/130778517078 ...and I have seen hub carriers like...
  5. D

    New GT40 build - GT40 Forte'

    Keith. Can you tell me more about the sill pod brace? What sort of misfortune lies ahead?
  6. D

    Looking for rear suspension a-frame and supporting assembly dimensions

    Mike. I am going to use this Sunday fabricating pieces out of PVC using the measurements you have provided. I really appreciate this Mike.. Thank you ^^
  7. D

    New GT40 build - GT40 Forte'

    It has been a while. I should drops some progress photos. Shell should be arriving soon.
  8. D

    Looking for rear suspension a-frame and supporting assembly dimensions

    Mike Pass. Absolutely. That would be perfect. My frame is a GT Forte' and I have it tacked up until the shell arrives. However, I need to have the wishbone assembly and rear uprights on the front burner. I can take your measurements and pump them into CAD and toy around a bit before...
  9. D

    Looking for rear suspension a-frame and supporting assembly dimensions

    Happy Weekend Gents, I have searched this forum and Googled a bit but can not seem to find any dimensional specs for the GT40 spaceframe rear a-frame and supporting assemblies. I believe I have what I need for the rear upper, I just need to get dimensions of "mainly" the rear a-frame. But all...
  10. D

    Looking for half shaft axles for my Advanced Automotion 01E with 108mm Porsche 930 output flanges

    I've taken a clearer photo of the output flanges used on my 01E purchase from Advanced Automation. I've not heard back from Scott on specifically what these flanges are used in (need this info to narrow my CV search). They seem to have the following markings: SCN DE 088355C and of course the...
  11. D

    Looking for half shaft axles for my Advanced Automotion 01E with 108mm Porsche 930 output flanges

    Hello Terry. That is correct. I have spot welded about 98% of the space frame (minus the roll cage ... waiting for spider to arrive before bending). The entire frame I can pickup and navigate it up and down by hand onto benches or onto 17 inch high standards for easy access. Everything is...
  12. D

    Looking for half shaft axles for my Advanced Automotion 01E with 108mm Porsche 930 output flanges

    Many kind thanks Ken Roberts. I was thinking so, but wanted to consider the possibility that I have goofed somewhere. I will work with Scott on this. Ken, could you please verify that I am considering the right process of building out my rear suspension? 1) Determine where the tranny/engine...
  13. D

    Looking for half shaft axles for my Advanced Automotion 01E with 108mm Porsche 930 output flanges

    Here are some photos. I am kind of thinking these flanges are not 108mm. I am not dogging/blaming Scott. Just trying to figure out what I am dealing with. The 3rd photo is of a flange measurement from a project site that I am using for contrast. Am I measuring wrong? Am I interpreting wrong?
  14. D

    Looking for half shaft axles for my Advanced Automotion 01E with 108mm Porsche 930 output flanges

    I have searched around and read through threads and could not find a applicable solution to my problem. I have a rebuilt 01E from Scott at Advanced Automotion and I have opted for the Porsche 830 108mm output flanges. I do know know exactly what uprights and hub carriers I will be going with...
  15. 20210511_215630.jpg

    20210511_215630.jpg

  16. 20210512_171728.jpg

    20210512_171728.jpg

  17. D

    GT40 Build - GT Forte' space frame - Question about front suspension

    Many thanks Mike. I certainly appreciate the time you have spent on your write-up (it has not been in vain). The past few days I have take a few measurements from my Mustang II kingpins and roughed out a my PVCAD model (Poly Vinyl Chloride Aided Design just to get a vague notion of what the...
  18. D

    GT40 Build - GT Forte' space frame - Question about front suspension

    Impressive Mr. Mike. Thank you kindly for this treasure trove of information. I will put it to good use :o)
Top