Search results

I'm repainting my car and will be painting on the roundels again. Anyone have a good code for the off white? I dont want vibrant white.

I have some left over laser cut "block plates" in stainless steel that are designed to fit between the Coyote motor and the Ricardo transaxle. They are perfectly laser cut and fill all the voids around the motor to transaxle area. I believe they should also be used for correct spacing. Images...

I have stuffed my Coyote engine in my RCR40 and I cannot find the engine number. Does anyone have a coyote out of the car and could you tell me (possibly with a photo) where the engine number is located? Thanks.

I want to install traction control on my car as the ECU will support it. I don't think I will need it due to lack of HP but it will be fun to setup:rolleyes: Has anyone on the forum installed traction control speed sensors on RCR uprights and bearing assemblies? Before I engineer my self...

Pair of RCR40 door handles. These are polished stainless steel. Free worldwide shipping. USD200. I can accept PayPal to make this easy. Just send an email to [email protected] if you are interested or have questions.

Can anyone with an RCR tell me the ground clearance they have? That is the distance from the bottom alloy plate (the main one that makes up the cabin floor) to the ground. My car currently has 95mm (just under 4") and I wonder if this is way lower than it should be. Rear lower arms are almost...

I may get a spray for this question but I cannot find an answer on the forums. I need to sense oil temperature on my Ricardo trans but do not want to plumb into the external oil lines. Is there a blank plug or similar on the case that I could measure oil temp from? I do not want to drill a...

Dear all I was looking at some GT40 images and came across this site regarding a recent GT40 accident. Is this Toms RCR 40? I know his car from the posts and it looks like it is. I am somewhat concerned for his well being. If this is not Toms car I apologise and moderators please remove this...

Can anyone tell me whether I should use the outer (slow) or inner (fast) steering arm position? There are two holes and I would like to know if I should setup bump etc for one or the other. Thanks.

Hi all, just looking for some advice. Is it OK to orient a filter as per below? Yes it will be fun to change but I can deal with that. The filter is before the cooler (hot oil goes through the filter easier) and the location assist routing hoses under the drive shaft (there will be protection...

Hi All. I have some parts that I will not be using in my car and would like to know if anyone is interested in them. Most have just $50 Australian on them. I have no idea what I paid for some of this as it was purchased in a kit. If the price is crazy give me an offer! Feel free to offer more...

Can anyone tell me if an increase in the height of the RCR GT40 by approx 4" is worthwhile. The gap at the top looks like lost cooling opportunity and a new taller radiator could fill the inlet fully. I can make a cap that blocks this, just thought that if I could replace this one with one a bit...

Can anyone advise if the Ricardo transaxle has an electrical reverse lockout? Is it the electrical connector near the selector shafts? Possibly a lock out solenoid or just the reverse lights indication? This could be a real stupid question but I do not think I'm selecting reverse (no running...

Has anyone got a good suggestion and possibly photos on how to modify the two front ducts to keep air out of the area where the headlight is fitted? I would like to modify the fiberglass in that area to push the air away from the light cavity keeping it clean. Any photos etc would be...

I have posted an issue with my RCR40's steering lock here: http://www.gt40s.com/forum/rcr-forum-rcr40-rcr70-p4-mkiv/28362-rcr-40-steering-lock-question-any-help-appreciated.html Unfortunately it must have been accidentally closed following Frans post without any clear resolution posted on...

Fran, following my initial question on this steering issue to you on the 14th of April 2009, and your request for further information on the 15th April 2009 (of which my email response with additional data was given to RCR almost immediately) I'm still yet to receive any response regarding...

I have a new set of bear claw latches supplied by RCR for sale on Ebay. Fair price (USD28.00 Buy it now) plus shipping. They could sit in the garage for years so its better to give them a new home! eBay Motors: Locking Large Bear Claw Door Latch Set (item 380098168551 end time Apr-19-09...

I fear that my whole body is too far back on the chassis. I have pushed the rockers to the rear (as recommended) to get front wheel clearance etc. but I think I have gone too far. The lower edge of my window seems further back compared to other photos on the forum. Can another RCR owner tell...

I have no need for a set of new RCR side window hinge hardware and am selling them CHEAP. Don't forget the Australian dollar is only worth 64 US cents! Also FREE airfreight shipping worlwide, none of this rubbish $40 for shipping such small parts! See it at the following link: GT40 Side...

Just looking for some info on the ride height for the RCR40. I know Dean Lampe has posted some heights but I do not know where they were taken. I was wondering if someone with an RCR on the ground and fully loaded could tell me the front and rear clearances from the bottom chassis plate to the...