Search results

Looking to buy an ETB DIgidash 2 Pro for my part inventory. RCR SLC kits used to come with them.

Figures that on my last drive of the season one of my CV boots decided to tear .. oh well, at least the grease slung everywhere made it obvious what the problem was. Does anybody know what the transaxle-side CV boot replacement is for a Ricardo? They're stamped KOK and BT-36 .... I think the...

kinda ... for one video ... lol

SOLD, no longer available LS3 525 crate engine. Approximately 1,200 miles. $4,800 shipped (shipping included to Canada/US; shipped as a pallet, likely to nearest depot but depending on location could possibly be to door) https://www.chevrolet.com/performance/crate-engines/ls376-525 1 -...

Does anybody know if the 9 bolts used to bolt the Stillen clutch to the flywheel (-n806178-s437 ) are reusable or single use?

My LS3 is starting to smoke a little bit at cold idle and recently fouled the spark plugs after a few hundred miles. Smoke is from both sides and all spark plugs were fouled evenly, so I don't think its valve seals. When I looked in the intake it had puddles of oil in it. I'm hoping that...

I have a non-inverted 930. At the top towards the front of the unit there is a swivel fitting that vents fluid. The fititng does not connect to anything, it just sits exposed there pointed rearwards. Any time it's really hot outside, driven hard or on the dyno the vent fitting pukes fluid...

I've been calling around for quotes on a 3 car detached garage expansion and people are trying to tell me $110-$150k. Da faq? For somebody with limited craftmanship skills, how dificult is it to build a garage? I imagine pieces like electrical and foundation should be subbed out, but the rest...

Hand-cut racing slicks w/ historical pattern 2x 9.1/23.5/15 (front) 2x 13.0/25.0/15 (rear) A11 compound 15" Historic all weather | Avon Motorsport $1000USD takes the 4 tires. Shipping will be exact cost to buyer (I'm guessing probably $200 ... I can ship the tires as is, or put them in a box...

Does anybody have any recommendations for fender-mounted mirrors that don't look like ass and offer acceptable rear visibility? So far the Vitaloni Sebring mirrors seems interesting - convex and look okay on a gt40 (no idea about a 917)...

My chassis is very stiff and when taking a steep left-hand turn going uphill (e.g., road-to-uphill-driveway) the front right tire ever-so-slightly lifts off the ground and the suspension is deloaded (i.e., spring flopping around with potential for spring hat to fall off). Right now my solution...

FS: Holley Dominator ECU + All LS Harnesses & Accessories $2,100USD Shipped. Virtually unused - I had it installed in my car with about 30 minutes of run time, but opted to go a different direction. Includes: -Dominator ECU V2 (firmware flashed to V4) -LSX fuel injector harness (for...

FS: Harrop LS3 Hurricane ITB Manifold (DBW) $3,600USD shipped (costs $5,500USD from Harrop after shipping/customs) Drive-by-wire version setup for the early model ETC ("silver" throttle body). I've bench tested it using a GMPP crate engine ECU setup for a late-model ETC ("gold" throttle...

I'm trying to understand if my front shock mount is in single or double shear and if this is okay (i think it is, but never seen a design like this) Two tabs are welded onto the lower control arm One of the tabs has a 1/2'' hole, the other side has a 1'' hole The side w/ the 1'' hole has a...

Are the suspension brackets that the UCAs and shocks bolt to plated/galvenized/etc... or should they be powerdercoated to prevent surface rust?

My steering rack travels through the chassis - the boot doesn't last too long before being torn to shreds. Is there such a thing as a ?cap? that only protects the very end (around the rack) as opposed to a boot that is several inches long? Short of that the only way I can see to solve my...

My charcoal canister is just a billet cylinder that is filled with charcoal; inlet (with a mesh screen) on the bottom, breather on the top. Because of space limitations the only way I can get to it and not form a p-trap with my hose is to run my vent hose to the top (inlet outlet) and let it...

I know a few of you are running the Harrop ITB with mesh filters (i.e., no air box). How are you plumbing the connections that normally go to the intake manifold/intake tubing, specifically the "snout" that exits the valley cover and the breather fittings on the valve covers. I'm thinking of...

I'm having trouble (maybe) finding reverse on my 930 transaxle. I can push the shifting rod all the way in/out (1,2), and I can turn it clockwise about 1/4'' or so and push it in/out (3,4). I've been told, and have read, that reverse in a 930 is turn counterclockwise and push in. But i can't...

Has anybody here extended their Dominator ECU DBW wiring harness from one of those companies that manufacturers extension harnesses (i.e., not by not by cutting/splicing wires yourself) For some reason Holley gives you like 50% less DBW wire (at the gas pedal) than the GMPP ecu box .... no way...