Search results

Hi Anyone here have plans to attend this event, “2015 Heacock Classic Gold Cup” Race Weekend held at the Virginia International Raceway (VIR) September 24 – 27, 2015 This would be about 10 hours each way for us. Just want an idea of who may be there before committing to making this trek...

From MSN Skydiver breaks sound barrier - Technology & science - Science | NBC News

I have had My third Slave Cylinder fail and fill the bellhousing with fluid in the last 1500 miles, These are the Audi units all made in Germany. Is this a pressure plate issue or are these cylinders prone to fail, Is there something better ??? Thanks Wally :sad:

Any ideas ??? Had the 1/4 turn plug in the engine compartment uncouple. Shutting the car down, Reconnected and now I can't get rid of the noise on the Ref Sync signals and it won't start. I have checked the wiring to both sensors back to the unit and they check good and the sensors do not...

With 1300 miles on the RF it lost the High Pressure fuel pump ( Bosch 0 580 646 070 ) Any suggestions for A better replacement ??? Looking for one that I don't have to worry if it will get Me back home or not. Thanks Wally

We've been out enjoying the 40 and here are a few pictures as requested. Let Me know what you think, One has My copilot in it ( She always gets asked why I let her drive. ) Wally

Hi after spending the last 4-5 hour wringing out wiring on the A.C. system on My R.F. I think I have an open wire ( looks to go into the harness under the dash, But I can't find it at the fuse block ) Went to the wiring book and they only tell you to plug this into that and it should all...

Anyone have the pinout for the 6 pin plug for a Smiths tach part # RVC 2490-00C4 The paperwork I have doesn't match the way the wiring harness is made and the tach is not working has power and ground only don't know if there right. The tach shows up on the motec software and all appears to be...

Have found that the Speedometer on the RF is reading High by about 10 MPH at 60. Are there gears available to correct this??? This has an AUDI box in it. I don't mind buying the gears and will check them against the GPS till I get the best match. Or how have you corrected this ??? Thanks...

The fuel gages are not working, If I ground the wiring harness the gage works. The senders have NO Resistance. Anyone have a replacement part # for these ??? Thanks Wally

Who is the Guy to Go to for Parts Ect for the Roaring Forties State side ??? I have some questions and will need to change some parts of as required for inspection & Safety. Or who and how do I get in contact with on the issues that I have. Thanks in advance. Wally

HI. Who is the Representative in the US. for Motec ??? Where can I get a USB to CAN adapter for a Motec M800 ??? Is there anyone in the OH, PA, NY. Corner that has experience with these units ??? Thanks Wally

We installed the Roll Cage, I was planning on adding tabs to attach the spider to the cage. My body guy said I'm asking for major problems if I do. Any thoughts ???????????? Thanks Wally

Looking for 50 OZ Flywheel to send with My 302 Crank to have balanced for the spare motor. Anyone have one ??? Thanks Wally

HI All anyone have any good pictures of the front Sway Bar for the GTD's. Were these a sourced part or were these from ???? Dimensions would be nice so I can see if this will fit this old chassis. Thanks

In an effort to attain a flat firewall I installed an Explorer water pump asm. Now I have 3/8 clearance instead of a 1 + " intrusion. I am concerned about the belt setup having enough surface area on the water pump as is I can mount the idler higher and closer to the water pump if necessary as...

HI I'm adding a Quick disconnect to my steering columb and want to know how far from the dash should the steering wheel set ??? As I have the columb out I can remount to make this distance correct. Thanks

HI I just unboxed the Gauges for the dash and the needle for the tach is loose behind the lens and I see no way of reattaching it. Any suggestions of who can repair this. Thanks :sad:

Hi Can anyone tell me what thread rivnuts were used on the KVA Chassis ??? I bought a box of 10-32 button heads and a tap. The tap wants to take material ( not just paint ) out of the one's in the chassis, Also the replacement Rivnuts that I picked up are way to small for the old holes. So where...

HI When removing the the Clutch from the flywheel, The disc had glued it's self to the flywheel. As this will be setting for ??? before I get everything hooked up is there any thing I can put on this at reassembly to prevent this from sticking again ?????