Search results

Vehicle is street legal, and Minnesota titled. Approximately 100 miles on the odometer. Vehicle is located in Minnesota. I started the initial build process, but eventually faced the fact that I was in way over my head, so I sent the car to Allan to be completed. Allan graciously squeezed the...

The GM wiring harness manual indicates that a 5000 ohm- 1/4 watt resistor is needed for the RPM signal. What I've done is soldered a 4700, followed by three 100's. The four soldered together makes for a rather long chain. Is there a better way to do this, and how should I go about protecting...

So as not to muck up Ken's build blog, I thought it best to start a new thread. I received my Pfadt adapter today, and was really expecting something larger than what it is. It's really quite tiny! I was holding off on buying the actual QR mechanism because I wanted to see just how close this...

Just wondering what everyone is using for inner door pulls? I'm looking for something that is production, not home fabricated.

I've been on the hunt for NYLON corrugated split loom wire cover (gray stripe), but haven't found a place that will sell short lengths. Most places, like Waytek, have a minimum purchase of 100'. I even went to the junk yard today, but was told "Yea, that's not something I would be interested in...

Ladies and gentlemen, I've been looking for the part in the photo, but am coming up empty handed. It would be used to isolate my radiator from the chassis. It's like a rubber grommet with two metal bushings (inserted in each side of the grommet) and a threaded screw through it. They may be...

I searched the forum for information regarding fuel sender units for the Koso gauges, but came up empty handed. I see that the Koso has a range of 100 ohms, and 510 ohms. Albeit more pricy, is there any reason this unit wouldn't work? RA9511-ISS - ISSPRO Inc. I've measured the tank depth to...

I'm working on installing my hydraulic front end lift kit, but have some questions. My original plan was to mount the rams on the top of the shock, which should make bleeding easier. However, when I do this the upper area of the ram does not seat completely to the cap. The cap has a beveled...

Working in smaller spaces is sometimes quite challenging, thus I needed to figure out where to store my center spider. My only idea was to hang it from the garage door rails. The garage door is a single-wide that is steel inside and out with insulation. So, I guestimate that it weighs more...

Yes, I am ignorant.:shy: Now that that is out of the way, I'm looking for some elementary information in the form of "What is this part called?". I appreciate the forum entertaining my benighted questions. Your answers will help me to refrain from making references such as "The upper...

Last month I went to RCR to see my car for the first time. Just thought I would share some photos. I'm still amazed at the cartoon sized width of the rear tires. Makes the tires on my Land Rover seem like something from a tricycle.

Anyone know how the '01 crew did at Summit Point today? I tried searching for lap times/finishes, but came up empty handed.

I thought it might be neat to see where all of the SL-C's have ended up at. So, I started a Google world map that shows the location of owners. If you are interested in adding your location (or approximate location) to the map, just shoot me a PM with your email addy. I'll send you an invite...

I've got a aluminum shift knob that I'm interested in using, and it is available in M10x1.5, M12x1.5, and M12x1.25. Can anyone tell me what the thread pitch is for the shift shaft of the SL-C? Cheers

I've taped the Stacy David's GearZ episodes in which they are building the SL-C. My problem is that the DVR is recording in VOB format. Can anyone suggest a safe and free video convertor source? Cheers

My SLC should be ready for transport from RCR soon, and I'm looking for transportation company suggestions. I had used Gran Turismo Motor Sports | Enclosed Auto Transport to get my Lotus home from California, and they did a good job. However, it was quite expensive. Thanks for the...

I see that several people are using the round Moroso expansion tank. There are 4 different sizes, so I'm wondering which one to get? Thanks much! Search Results for Moroso Cooling System Expansion Tanks - SummitRacing.com

As luck would have it, the orange SLC mule was sold just prior to my visit at RCR. I'm wondering if someone might be willing to send me photos. The more detailed the photos are, the better. :thumbsup: Cheers

Happy Thanksgiving everyone! Turkey is in the oven and should be ready in 40 minutes! BTW, I ate an entire pumpkin pie for breakfast:D

I've been on the hunt for tires, and am having a hard time sourcing the proper sizes from a single vendor (Upgraded wheels). Just wondering who people are using? Sizes I'm looking for: 295/35/18 345/30/18 or 335/30/18 I'm open to different tire size suggestions. I had the Toyo Proxes r888's...