Search results

I`am in search for a set of four of the Hartwell style front and rear latches if anyone has a set please drop me a message. thank you!

I`m going to run AN4 from my clutch pedal to my G50 Slave Cylinder I`m looking for help on the thread pitch size on the slave cylinder threads any of you recall what size it is? thank you all so much for your help. Kent

Any of you using the TWM 48 IDA,s recall what the thread pitch is on your fuel rails? I can thread and 8AN into the rail but I was told it could also be metric? any help would be greatly appreciated. thank you. Kent

Where can I purchase the aluminum fuel logs that connect the two fuel rails together I see on some of the 8 stack injection systems thank you for your help. Kent

Looking for advice.. I have a 351W it is internally balanced, I`m using CVF racing pulleys ,4 bolt harmonic balancer pulley and a CVF short water pump what would be recommended for the harmonic balancer to make belt alignment the easiest. Thanks for all your help Kent

Looking for a brake line diagram, I want to run a 3AN line off of the calipers on all for corners of my car and from the braided lines go to 3/16 hard lines..but I`m unsure of where to use proportioning valves and residual pressure valves or anything else I mite need to add to the brake line...

On my GT40 I have and 8 stack weber EFI where is the best place to mount the intake air temp sensor for the sensor to work and monitor temps the best? do any of the manufacturers make a bracket to mount the sensor? if not I will just fab one based on the best place to mount the sensor. Thank you!

I`m slowly making forward progress! looking for advice on AN fuel line size, from the fuel tank to to the weber 8 stack injection 351W 6AN or 8AN ? thank you for your advice.

I`am very close to finishing up on my AC and ALT brackets thanks to the help from forum members, is there a Sanden compressor that has Similar mounting brackets on the compressor as the sander model 508 does but a little smaller? I can get the 508 in ok but my range of belt adjustment is very...

I`m looking for a low mount left hand side a/c compressor bracket for my build its a 351W any suggestions would be greatly appreciated. thank you!

I`m in search of a low mount right hand side alternator bracket for my build its a 351W any help would be appreciated ,thank you!

I`am looking for advice or recommendations on who to contact to have half shafts made for my GT40 build? I`m located in central Minnesota.

I`m looking for a pedal box for my Build just thought i would check to see if any of you had anything for sale, i`m looking for a floor mount...

I`m looking for a set of headers, bundle of snakes and heat shield, for my GT40 project its a 351W 408 stroker with 185 CNC trick flow heads. you can send me a message or email me at [email protected] or call 320 295 1335 Thanks

I`m looking for advice on where to purchase a slave cylinder for my Sabre GT40 I`m using the 5 speed g50 box which has been flipped,with a new 2006 Ford GT40 clutch pressure plate and flywheel, with a Patrick motorsports cable shift setup. Thank! Kent

I`m looking for a left hand outside door handle for my GT40 build I have everything else just hoping to find the handle thanks! Kent

I`m looking for a pair LH/ RH Door Boxes For My GT40 Build any help in finding where to purchase them would be of great help thanks and have a great day! Kent

I`m using a 5 speed G50 in my GT40 build, I`m looking for advice and/or drawings from anyone who may have fabricated the mount I`m looking for help or drawings from trans to chassis mounts thanks Kent

I`am looking to buy a pair of GT40 seats new or used or recovered.

I Purchased the Sabre GT40 that has been bought and sold a few times on this Awesome forum...I have made a lot of headway with the car since picking it up in Texas in June, I will be posting pics on my build log soon.