Search results

Very Very nice Ross, in fact thats just what my WIFE and I are in the market for ... nice little 2 bedroom house and a adequate 3 car garage. Have you any plans in place for up grading the sound system? All the best , Burnsy.

Bill , I have a mechanical drive. I`m in the process of tyre selection (17 inch),there apears to be a lot to choose from and a variety of diameters. Regards,Burns.

Can anyone advise the correct rear tyre diameter or a allowable range that will keep my speedometer error within ADR 18/03 requirements. I have a 5 speed AAZ-016 and RF 300kmh speedo Thanks,Burns RF#104

Tim, Nice pictures and stunning paint job! the "Milano Red and Silver " work well together. It was good to see the new 17" BRM`s on a car, I`m still waiting for my set to arrive in Aus. They do look great. Are you using the 275/40/17 tyres on 9.5" rims? I`m currently looking at...

HUW,Yes the rear two ports are for water ( cooling ). Link them together and connect to the thermostat housing as RICKY states I have just filled my system and had no problems at all. I only cracked the above mentioned ports and topped up the expansion tank slowy till coolant escaped from...

Peter, I have often wondered what those sockets are provided for - especially in that location so will check it out for sure! I just tried ringing you prior to coming inside and checking the forum. Thanks, Burns RF #104

Paul, Sorry for the delay in responding, I am trying to start-up for the first time and still having problems. It runs up to about 500rpm then dies -firing occasionally after that while cranking, it still appears to be a timing problem I am currently trying to use Motec`s engine log and...

Thanks Ross, I am using magnetic sensors which dont use a power supply however I have found a drawing for motec - magnetic sensors showing trigger voltage levels as 0.25V min <500 rpm 1.40V min >500 rpm So 0.4V should be O.K. at crank ( rpm...

My M800 has a ERROR-sync signal that keeps coming up on cranking (I have magnetic sensors) The Engine fires on the first cycle then no ignition (spark) after that...... On the Utilities ref/sync capture screen I have Ref Voltage -1.5V to +1.5V Sync Voltage -0.4V to...

Pat ,I also have a DC&O manifold that has the throttle bodys linked in pairs,I`m about to start up so am interested in what you turn up with this post. Advice to date indicates problems on deceleration and low revs with backfire ____________________ burnsy RF104

Bill, I`m about to start my RF for the first time after 2years build time ,the car is 95% complete and is in a flat black sealer for now,it looks mean! ...my boys don`t want me to paint it, but I will take the time after the major bugs are sorted out to strip it and just concentrate on the...

Thanks Ross, I`ll get back on the trail again, a lot of parts used are GMH so it would come as no surprise if one fits. The bypass is all sorted Burns

Rick thanks for the offer ,you have a PM also ___________________ Cheers Burns RF#104

I am looking looking for a set of headers or complete system that fit`s a RF 302 crossover or standard with cats. lend, hire ,buy I`m looking at start-up and rego options for now. Regards Burns.

Guys,could anyone advise on which thermostat housing -make /model fit`s a 302 8 barrel setup.....also any advise on the hoses that connect to coolant pipes would be most helpful Regards, Burns.

Thanks,Mick, lots of good pic`s on site.... will contact you there. Regards, Burns.

Has anyone used a GT40 Australia mount on a RF chassis? I`m interested to see how it sits on the chassis pad Burnsy

Peter,I have the black wire to sender body and the brown wire on T which seems to work ok Burns

Thanks to everyone for offers of help and advice for RF owners still in the construction phase, I had leather seats - ss eyelets on order to meet ADR`S. Now looking for a new source of supply! Regards,Burnsy RF 104.

Burns Mckay RF #104 Currently working towards PAINT!