PW Tornado Build pics - Page 4

Paul W · 08-12-04, 05:00 PM

I've been snowed under at work for the past couple of weeks so not much progress - anyway here's an update.
Rear window cut out of bulkhead.

Paul W · 08-12-04, 05:03 PM

Made a bracket to hold the rear clip when it's open.

Paul W · 08-12-04, 05:06 PM

Did my first bit of fibreglass molding and made some headlight rear covers.
And a bracket to hold the front clip.

Murray Cowley · 08-12-04, 06:50 PM

Pretty neat Paul, I like the 7 series lights in there, but just as a matter of interest, where are your indicators going to be ? Nice work, I still cannot get to work on mine yet, don't ask, it's a long story!
Murray

Paul W · 08-12-04, 07:52 PM

Hi Murray,

I haven't decided what to do yet - kind of depends on what I can get. There is enough space to put a small bulb next to the driving light - maybe the small round peugeot unit I've seen on a few cars. Ideally I can also find one of the round domed amber glass units to put on the outside of the wing between the light lenses and the wheel arch - like some of the originals had.

Brett James-McCall · 08-13-04, 04:55 AM

Paul,
Are you going SVA, as if you did that it would not pass (if I am visualising correctly), remember the angles that 50% of the unit has to be seen from....

Brett

Paul W · 08-13-04, 07:23 AM

I think for SVA you have to mount an indicator inside the headlamp recess temporarily as It's too low elsewhere - also if the front clip is open you need to be able to see the hazard lights. I think you just make the front clip open about 2 foot from the base of the screen.
Nice job on the mag by the way.

P.

Brett James-McCall · 08-13-04, 12:10 PM

Paul,
As a thought, if ou were going to go Gulf colours, then you could put a square indicator in the front of the headlight recess, like some of the JWA cars?

Brett

Paul W · 08-27-04, 06:24 PM

Forgot to post this a while ago. Plenumb chamber air scoops.

Paul W · 08-27-04, 06:27 PM

Engine front cover - needs a bulge fitting into it once I get the engine fitted.

Paul W · 09-13-04, 01:18 PM

Radiator fitted.

Paul W · 09-13-04, 01:19 PM

Dash fitted.

Bill Bayard · 09-13-04, 01:59 PM

Paul,

Do you work on that thing 24/7, or what?

Amazing progress!!!

Looking good!!!

Bill

Paul W · 09-13-04, 03:24 PM

Thanks Bill - I had a few weeks off work when I first got the kit so got loads done. I haven't actually had much time lately as work got busy again but things should calm down a bit for the next few weeks. I'm fortunate in the fact that I get days off in the week so I never get stuck for a part because the shops are shut. I picked up a few parts last week so I'm now fitting them.

Paul W · 09-16-04, 07:37 PM

Rear window fitted.

Ron Earp · 09-16-04, 10:06 PM

That glass work looks good on the doors and the fit. Nice work and it looks like Tornado has good bits there.

Paul W · 09-17-04, 08:05 AM

Thanks Ron - I just bought a flat piece of polycarb from a local plastic supplier and cut it to size. My doors are actually just sat on small blocks of wood to check the spider fits ok - it's going to have to come off in a couple of weeks as I'm having a rollbar put in. I seem to have got the drivers side of the spider perfect but can't seem to get the passenger side right - it's perfect apart from the corner nearest the rear viem mirror sits 1/4 inch high. I'm wondering if the door lift brackets will be strong enough to pull it down into place.

Paul W · 09-19-04, 07:48 PM

Light lenses and indicator on.

Paul W · 09-27-04, 08:30 PM

The engine's in.

Paul W · 11-03-04, 03:42 PM

Fans fitted.