sswartz's latest activity

  • sswartz
    sswartz replied to the thread Air ride slc ?.
    I'm not aware of anyone that's implemented an air ride. Many street SL-Cs, including myself, use a hydraulic lift up front. You could...
  • sswartz
    sswartz replied to the thread S2's Build Thread.
    Joel, I will control it via a MoTeC ECU. If I wasn't going in that direction, I'd take a serious look at Fuelab's motor controller...
    • 1568425043645.png
    • Fuelab Fuel Pump Certification.jpg
  • sswartz
    sswartz replied to the thread S2's Build Thread.
    I spent a lot of time looking for a fuel pump with the following requirements: 1,000+ HP; it’s gotta have the juice. Brushless: Heats...
    • 1568288286803.png
    • 1568288375346.png
    • 1568288506848.png
  • sswartz
    sswartz replied to the thread LSA SLC Build Log.
    I have the HiSpecs, so let me know if you need any measurements
  • sswartz
    sswartz replied to the thread S2's Build Thread.
    Dan, I'm going forward with variant 2.6-A3, which looks the best, but requires the most work. Funny how it always seems to work out that...
    • 1567983246645.png
    • 1567983374723.png
    • 1567983420578.png
    • 1567983472403.png
  • sswartz
    sswartz replied to the thread S2's Build Thread.
    I took a six-week vacation with the family and, fearing build withdraw, I made a man bag to bring some electronics along. Needless to...
    • 1567519168235.png
    • CC131253_hi.jpg
  • sswartz
    sswartz replied to the thread Joel’s SL-C Build Thread.
    Joel. I have a Pro Street EPAS and a Pro 102 tilt column on order. My understanding is that the column is collapsible. I have heard...
  • sswartz
    sswartz replied to the thread Residual Valve Recommendations?.
    Steve, all of the Daily pans that I have seen have the pump integrated into the pan. If you can’t find two -10 sized outlets in the pan...
  • sswartz
    sswartz replied to the thread SLC Hubs/ race worthy.
    I exchanged brief texts with Fran today. There are new front and rear uprights. The center section of the upright and spacer will be...
  • sswartz
    sswartz replied to the thread S2's Build Thread.
    Mesa, I think you're talking about 2.5 above, but with the black side scoops. Below are three renderings with increased vent heights...
    • Vent-Height-Variations.jpg
  • sswartz
    sswartz replied to the thread Residual Valve Recommendations?.
    Steve, I saw that picture in the PDF you attached, It only shows the pump and not the pan. The scavenge inlets have to pull the oil from...
  • sswartz
    sswartz replied to the thread Residual Valve Recommendations?.
    Steve, my pump doesn't have any scavenge inlets. My guess is that my pan has all of the scavenge lines CNC'd into the pan and that the...
  • sswartz
    sswartz replied to the thread Residual Valve Recommendations?.
    Steve, here's what I'm doing for my Daily dry sump / Peterson for a LS. The recommended scavenge filter is huge 9.7" x 2.5" with -16...
  • sswartz
    sswartz replied to the thread S2's Build Thread.
    I should have put the image series in order (i.e., 1, 2, 3, 4). My choices so far are: 1.2 (roof scoop delete) 2.8 (angled farther back...
  • sswartz
    sswartz replied to the thread S2's Build Thread.
    The SL-C has been around a while and still looks great, but I’d like to modernize it a bit. Before I embark on changing the tail as...
Top