Search results

Working with the driver's seat I noticed the steering wheel center is off by 2 to 2 1/2 inches to the right from the center of the seat. I have the seat as far over as possible to the shifter. These are not the gentlemen seats. Should I try to move the steering column? I believe it may throw...

I need a picture of the top brackets for mounting a fiberglasss wing on a race tail. I have the uprights installed but need a picture of the brackets to the wings and how they are mounted. The wing is the newer style and Allan's video has the old mounts.

Car looks great! Where did you get the engine coil pack/fuel rail cover? That is something I been looking for.

Any pictures of the connection to the caliper?

I am in the process of running the parking brake cable and what like to see how some of the builders ran the cable up to the caliper. I am planning to have the handle in the middle of the vehicle since my fuel system has taken all the space available on the left side of the driver.

Mike the picture are great. I have a question on the wing bracket and diffuser. Were the wing stand off brackets in the kit? Also, did you modify the diffuser for clearance for the mufflers?

What column is RCR supplying with their kits today? My column has no power telescopic or tilt, only manual tilt. Also, is there suppose to be a cover with the column? Mine does not and looks unfinished. I would like to use the NRG system but don't know which to purchase.

Are the wing struts from RCR suppose to be bent like Yos's car? My are straight like Eric's. It's going to be pretty hard to bent them without a heavy duty metal brake!

Can the MAF sensor be located in one of tubes after the tee? I know the GM manual calls for a minimum of 10 inches from the throttle body with a minimum of 6 inches of straight 4" tubing. The picture in the FFcar option guides shows a small tube (less then 6") from the throttle body to the tee...

Does anyone know if the GTM optional Cold Air Intake system will work on the SLC? The GTM has a tee from the throttle body to two tubes forward of the rear wheels? I have the race tail option and if the single tube with the 22 degree downturn has an interference problem I am looking at...

PM sent.

With the new design evaporator case from vintage air what fittings are you using to connect the #10 hose? The older model had the #10 on the bottom and a 90 degree fitting would work. With it on the top and the #6 on the bottom not sure want will work. A straight runs into the passenger side...

I am in the process of installing the vintage air evaporator and was watching Allan's video and noted that my evaporator is different. The 5/8 radiator hose fittings are on the same side as the #6 and #10 fittings. Also, in Allan's video the the #6 hose from the dryer is above the #10 from the...

I am in the process of completing the brake system and watched Allan's video on the residual brake valve and have taken both brass fitting out of the 2lb valve. The problem I see is with the smaller stainless steel fitting supplied as seen from Allan's video that replaces the brass fitting...

Any SLCs being built in the Tampa area?

Starting the wiring on the SL-C and have a question on the a/c compressor. The ISIS manual indicates that the tan wire goes to the a/c compressor. The a/c compressor only has one wire (black). The kit also comes with a a/c ground wire. Do I just connect the tan (iSIS wire) to the black a/c...

Can you supply the part numbers? Thanks

I am at the stage where I need to run the a/c and heater hoses down the passenger side of the car and would like to see how other builders accomplished this task. Pictures would be appreciated. Thanks

Has anyone had a problem with plugging in the steering column to the ISIS wiring? In reviewing Allan's video and other build blogs my supplied steering column is different. There is no electric motor. The steering column male plug will not mate up to the ISIS steering column female plug...

Does anyone have any good pictures for the installation of the one piece adjustable pedal brackets? I reviewed Alan's video but my adjustable brackets are completely different. Not direction came with the kit. Thanks