Search results

Hi Dave. The Edelbrock performer RPM package with your carb will make a real 325-340 bhp ish on an engine dyno. I went down the route of importing AFR 165 heads on the back of various US based mustang magazines that showed collosal horsepower from the AFR's. After further upgrading to a 331...

It can also be a 302 cam , but one used for the HO series engines. Most of which built beyond around the early 90's are High Output "HO" engines.

I just did my tanks for the same reason. Everyone said it fails to pieces. So i bought the yellow stuff sold on ebay in small cubes. Whe i took my 17 year old tanks apart, i found the old foam fitted (yellow cubes) was perfect and exactly the same as the new stuff i was about to put in! Try...

Hi Francis. Thanks very much for your generous offer. Unfortunatley the 8inch diameter section would foul my electric waterpump. I need the diameter to not exceed 7 inches. Thanks again though,you thought is much appreciated. cheers jason

Wanted double row v belt crank pulley (4 bolt pattern) for ford 302. Anything considered!

Stew You need to recommend the rpm range your looking for and torque charachteristics. If you download Camquest from the comp cams site that is a good starter. Although be warned the quoted Hp levels are a tad on the side of optimistic! it will ask for the complete spec of your engine and...

thats what i thought too, can anyone else confirm ?

Hi all Im doing a 2 stage air con install. First my aim is simply to get an engine mounted compressor fitted, then run the car for 6 months, then complete the air con installation over the winter. i have the sanden type compressor fitted on the engine, and prior to the engine re-install i...

Spare ticket going for a Gt40 in the club. Not required as unfortunately car is poorly and need to take more mundane transport! £20( first class post delivered) call jason 07854 809021

Ive just bought some in Alcantara and with Leatherette outers. They look great and cost £500 plus vat, i think the leather ones are about £125 more. This includes ringlets I had seats from intatrim before and they are very strong and lightweight, There is certainley no flexing at all and the...

Simon I have this exact waterpump on my car . The pump seems to work well. However it is an awful design ,This is because the main outlet comes out of the pump body at the wrong angle. This means that when you screw in the pipe adaptor into the pump,it is impossible to put a hose on to the...

Hi there. The Comp cams part number you listed i think is suited for flat tappets. You might want to check the XE266H, which has a little less duration and a little more lift but suits the 1600 -5600 rpm range well. Make sure you have 9.5:1 compression to get the best out of them. the higher...

Lovely, can i ask how they cost ?

Having lots of problems trying to start my ford 302 after it came back from the dyno. The main change since my previous installation is the change from facet silver top to red tops. The new pumps continually tick where as the silver tops used to stop ticking when the fuel bowl on my Holley...

Steve thats great i'll send a mail No luck with the ford dealer, anyone with a left hand thread nut!?

Does anyone know a source for obtaining these nuts ? i need a left hand and right hand thread nut , they are around 21/22mm thread diameter ( or probably 7/8 imperial) Unfortunately my old ones seem to have worn out the nylon section and im pretty stuck finding them! thanks

an incredible day, just have a look at this lot, quite amazing. I've posted a lot of 917 pics on the canam/917 section later on, after all there were a dozen of them!

Incredible line up of cars were at Goodwood yesterday, i think 12 917's . included were 2 gulf cars, martini longtail, David pipers short tail, richard attwood at the wheel of his 1970 le mans winner, the 1971 winning car from the porsche museum various spyder versions plus the incredible...

I used Tim adams racing in Market Drayton, he was spot on with mine and knew exactly what settings to use after only one run on a dyno. He Achieved a perfect transistion from idle to full throttle. Very impressed and very reasonable pricing Tim Adams Racing Engines Unit C14 Rosehill...

Does anybody have any renault/Ford driveshaft adaptors they no longer want? May be interested in the Cv joints too if available. If so drop me a reply with your price.thanks