Search results

Alan, The other guy comment was directed squarely at you. I dont see any point in arguing with you about my opinion. And as an aside, I have worn out a small craftsman compressor..........and countless other tools! :O)

Alan, The other guy has to make his own decision. I have oil-less and lubed, single stage, and two-stage compressors from 30gal up to 120gal tanks. (I don't really see much of a difference in noise levels between any of them) They are ALL loud!! That being said, the advice to buy as big a...

Tom, Any tool that is continuous duty like a sand blaster or sander needs a large tank. I would not buy any compressor smaller than 80 gallons. You can use 2 stage compressors with smaller tanks like 30-40gal, but you will have to start and stop a lot. Spend a few hundred more and get the...

Chris, Thanks for the info! Got the bump steer kit and spacers yesterday in the mail. Thanks for taking the time to support the rest of us. Sincerely, Scott

Chris, Replied to your pm. This is an important facet of any performance vehicle! As an aside, at ride-height, are your front and rear control arms level? Ron mentioned this in his build thread, but when I looked at the set-up used for tracking by another member he noted they were not...

Chris, Nice job! That is the next step on my chassis as well. I had to lower my car down pretty far and run 2 degrees of negative camber in the front before it cornered well. Would you mind posting the part numbers/manufacturer of the inner tie-rods? Thanks for the info and write-up, Scott

Jon, The gt40 does attract a lot of attention. If all you are concerned about is attention, there are other cars that garner that kind of attention without all the effort you will be putting into one of these projects. The other thing to consider is comfort. The gt is hot and cramped, and the...

DaveM, Photo 4 looks like a spinner knock-off tool. Handy if you want to keep the spinners. I replaced mine with 3inch nuts and use a 1inch air impact/gun. Much easier, and I will never do the spinners again! Scott

Dave, My rollbars are hollow steel from speedway motors. I have an RCR, and you can look at how they mount on "Toms track-racer" build thread. If you want I will measure them and get the part numbers. The originals used solid bars that were "thinner" than the one-inch ones I have...

Keith, No mystery. People don't have to deal directly with the consequence of their actions on the internet. Being upset with what someone says or does is quite alright. How one responds is the true test of character......... I heard a good quote last night,"A man without his word is...

Cliff, The car was owned by Wayne Presley over on the ffcobra site if I remember correctly. He noted she was smokin hot without any makeup!! :O) Nice clip for the movie story-line next to your car. Kudos, Scott P.S. I have those "somewhat unique" camaro mirrors on my car too!

Delynn, are the units in stock ready to ship? If not, how long from order to shipping date? Thanks, Scott

Cliff, You are officially a rockstar! :O) MHNCO, Thanks for posting, neat to see videos of some of our cars on here taken by spotters. Scott

I have been reading this thread from the start as I used to race juniors and senior 2s at a national level. I also have experience with steroids and other drugs used to "enhance" an athletes performance. I think its pretty clear LA was using "something." However, considering that he was able...

Stephane, PM sent, Scott

Phil, PM sent, Scott

Veek, That was something (the lack of advertising) I found interesting as well too....... I am a movie nut, and see most of the new stuff that comes out. I heard nothing about this film until a friend called and spoke about it. I am looking forward to it.

Anyone seen the new movie "2016", or care to comment? (sorry if I am playing a little "lonesome BOB", but I do enjoy the mostly friendly banter of political views you all share) I will check back in after watching it this week, Scott

Dave, PM sent, Scott

Steve, At a minimum it will need a front clip, (2,500 for just fiberglass), suspension front and rear (probably frame and control arms need replacement), (wheels/axles),and quite possibly transmission looking at how hard the hit was to the rear........... If one could do all the work and was...