Search results

This picture better shows the black cover that I removed from both units. The wire grommet for the wires to passthrough easily popped out as well. https://www.amazon.com/dp/B09QYHY376?ref=ppx_yo2ov_dt_b_product_details&th=1

Finally finished the radiator hoses. We just went to the local autoparts store and looked around their in stock selection for radiator hose bends that seemed useful. It was a better deal than just buying 90 degree universal hose. I wanted a coolant temp sensor for after the radiator to monitor...

Hey Randy, I am investigating this now as well. TBD on if high speed bypass vents are necessary for this application.

Next up was the fuel filler tubes and caps! We took heavy inspiration here from Sean's build and used 2" stainless. (aluminum is out bc well..... you all have seen my aluminum welds) First I mocked it up using the 3D printed modeling blocks I posted about previously that were intended to be...

We finished mounting the radiator fans which is exciting. We mounted them using a fan shroud we built with some scrap aluminum sheeting we had in inventory. There isn't room to offset the fan shroud due to the front nostril panel, so there isn't room to bolt the fans simply through the...

There was one final coolant line that needed built that connects the bottom of the expansion tank to the return coolant tube. The coolant tube hookup point is just upstream from the water pump. To connect the line to the coolant tube the easiest thing I could think of what to simply weld in an...

keep us updated!

Welcome!! I am neck deep in an RCR40 just outside Columbus! Check out my build thread to see where I am at and let me know if you have any questions. I’m excited to have another Ohio builder on the forum!! Very jealous of the NSX…

amazon link above is an amazon link. Canton racing makes one very similar but its much more expensive. I've also seen Moroso make an identical one again for a lot more money.

Thanks for the info, but it seems that is for the amber turn signal lamp. Sorry I should have been more specific I am looking for the clear rectangular fog light lens.

Hoping someone who regularly checks my build log can help me find these front fog lights shown below. I didn't have any luck posting in the exterior section of this website... I am aware of the Marchal 651 lenses and the Ford Capri mk1/Ford Escort mk1 lenses that were originally used, but to be...

The steering wheel angle is perfect in my opinion. I carefully adjusted it for what felt like hours before finally drilling and bolting it in lol. I was worried about the pedal height as well, but I realized I plan to install a lot in insulation any ways, in addition to carpet. I think I'll...

We went to mount the pedals and decided last minute to just take the time now to cut a slot in the tray.... the pedals and my feet fit SO much better, especially with the pedal slider lifting up the whole pedal assy. It was worth the time. I just made a quick offset bracket then to bolt the heim...

Do you have measurements of them?

Those look pretty good thanks for the tip. They seem to be a little different from what I am seeing though, most notably more rounded and taller. What I’m seeing is more rectangular and slightly more narrow.

Hey everyone, I am looking for the latest fog light lense I am seeing often on these cars. I really like the look of the small rectangular light above the amber turn signal. From digging through this website the most I found is that they used to be a Marchal 651 light, but they are quite hard...

I may end up cutting a hole as well. Still thinking it over....

The expansion tank is in, and I think I picked out a overflow/recovery tank that fits just behind the fuel swirl pot. The line to the recover tank isn't mounted yet. The expansion tank is plumbed into the steam ports at all four corners of the LS "steam ports" and then the bottom of the tank...

Finally (mostly) done with the fuel system. It was a ton of work to get it how we wanted. The regulator is mounted out of the way of a cardboard box that will hopefully soon be replaced by a coolant expansion tank. Still waiting on a few fitting to finish of the high pressure loop through the...

G96/01! TBD how well it performs. I went for a limited slip as well.