Search results

Update. Paid a visit to the local Audi dealer. You can’t buy the sync ring separatly, it’s a ”kit” containing 19,20,24,25 and 26. And the price-$460. Guess it’s acceptable, in my dreams last night it was a lot more. I’m glad I woke up from that dream. I’ll have it here in 3 days.

Roger, I’ve seen the movie and I can say I had a feeling of Deja vu.

Well, it was a beginning of a small crack. I placed the sync ring on the gear where it`s supposed to sit (on the cone) and tapped it quite lightly and it broke right off. So,not a good weekend. The only good thing about this is that I discovered it now, not later, 100 miles from home. Wonder how...

The transmission is back together. Well almost. Everything went smooth until we should install the Transmission cover (housing), when I lifted it from my working bench a washer fell to the floor. My buddy and I looked at each other and said, where the heck did that come from. I will say that...

My good friend Calle made me the special socket today, now I’m just waiting for the 3 nuts, they should be here tomorrow. I’ll post the assembly this weekend as well.

Ken, do you have the approximate measurements and depth of the pull down handles.

Last week I made a CAI, cold air intake. Started with a big Fuzzy Dice, I made it out of two washer fluid containers, then cut it up. Also made a mount for the Dice in aluminium. Proceded with a plug for the intake itself. I made it out of low desity PU foam, very easy to sculpture/sand. Then a...

Joel, I took a couple of pics of the EWP, it very tight most due to my extension of the air duct.

Up until now I`ve had the Graz KBA (unmodified) in the car and this saturday I decided to swap to my KVJ (modified drop gear). Everything went smooth until the last thing to tighten, the drive shafts. As it turns out Audi apparently changed the diameter of the bolt circle on the transmission...

Where did you get hold of the catalogue with the part numbers?

Thanks a lot Dusty. So the 086307304 is for the prop shaft or should I order 3 of the 086307303 if reinstalling the propshaft?

Welcome to the club Dusty. Everything I need for the car is about 50% more expensive when I get it compared to over there. Anyway, I’m doing the drop gear on my KBA tomorrow. Do you have the correct part no for the 3 nuts that’s required? I would apreciate it very much.

Ken just think about fiberglass is a living material, it doesn’t like static pressure. Put a half full beercan on the rooftop and you will have a noticeable indent after 6 months. I would make some kind of reinforcement on the body to spread the load before you put any pressure on the leveling...

I have a Davies Craig as well, just haven’t installed it. The engine stays within temp limits so far so I’ll keep it as is for now. The climate here close to the north pole might help also.

Well it isn’t as bad as it lookes in the picture, I have about 8-10mm clearance.

Not a bad idea with the fitting. I have the dxb mufflers, they are pretty quite.

Cam, thinking about it you might have a problem with the length of the flat 4wire bundle if you run them both in the same side pod. Since I ran mine in the center they are equal length and I cut approximatly 80-90 cm off of them. If you run a wire in each sidepod-no problem. Just measure the...

Cam, I ran my wires through the center console and they are quite a bit stiffer than round wires, but there is no problem to route them as long as you don’t have a super tight radius. Only thing i regret is not choosing the pushbutton version since all my other switches has that design.

Howard, I believe it was this one you recommended long time ago. And yes Joel, it acts as a booster together with the mechanical and is a flow thru, so it doesn’t have to run continously. I mounted it just before the radiator inlet, just made a new bracket to get it inline with the inlet tube...

Sorry Joel,I forgot to take a picture of the pump installed and you can’t hardly see it now. This is the pump I have. https://www.stewartcomponents.com/index.php?route=product/product&path=63&product_id=69