Search results

That's an interesting idea with the gated shifter. I wonder how this issue is handled in the R8? (I've never driven one) As it stands with the Graziano in my SLC, finding first gear is by trial and error and reverse is not protected except by its position. I'm sure the R8 must have addressed...

I'm curious as to why you decided not to go with the Shorai battery? I have used Shorai for other projects and was thinking of using their larger one (LFX36) for the SLC. . .

Hi Craig, I'm not sure, but as no one else has responded yet; I believe it is GL-4. Don't forget to include a loop for the oil to circulate if you haven't installed a transmission oil cooler. Dave

For those with Graziano's: How strong is your centering spring? On mine, if I manually push the lever on the transmission, it returns to center but not with much force. With the cable connected at the transmission end only and extended straight out with the dust covers removed, it will still...

Ken: Have you had a chance to try out your front wheel sensors? I'm wondering if the holes adjacent to the wheel studs cause any problems with the sensor count? Is this something that can be adjusted out with the gap to the sensor?

I hope so - that's what I did, but it hasn't run yet . . .

I exchanged emails with the guys at Racelogic and asked if they had any tips or thoughts for installing their system on an LS7 engine. They said that the LS7 may have misfire detection and that this would need to be disabled. I have the GM aftermarket ECU. Does anyone know if this ECU has...

Thanks for the tips, guys! I just re-read the instructions on pg. 24 of the ISIS installation guide ("Connecting the Cooling Fan Trigger Wire to the GM Fuse Box") and it says to simply connect the GM fuse box cooling fan output wire directly to the identified ISIS wire. I couldn't find anything...

Does anyone have any suggestions for how to build a saddle to support the back of the intake? (see arrow in picture). Thanks for any tips!

I'm confused. Doesn't an invert module take a 12 v output from the ISIS system and use it to trigger a ground? Why would this module be required for either the air conditioning compressor or the fans? Isn't the Vintage compressor already grounded through its case and therefore requires a 12 v...

Great pictures - thanks! Are you using any of these sensors for your speedometer?

If you use the toothed wheel on the half-shafts in back, what would you use on the front? Can the Racelogic system handle wheel speed sensors which have a different number of cogs/counts on each wheel? Also, is it possible to split the output from one sensor to both the traction control...

Has anyone hooked up their speedometer to a Graziano yet? If so, what are you using for the sensor? Can the Input Shaft sensor be used for this and if so, what needs to connect to each of the two pins on the sensor? Thanks for any advice.

With the help of a welder friend, we just finished the rear exhaust on my LS7/Graziano. Here is what we did: Parts: 1) 2 FlowMaster Hushpower DBX mufflers http://www.summitracing.com/parts/flo-13014310 2) 1 U-Bend http://www.summitracing.com/parts/sum-622004-ss 3) 2 clamps...

I received the cable ends from RCR a couple of weeks ago. One of the ends fit fine (the one that snaps over the ball joint), but the other was a rod end that fit fine over the post, but was designed for a 10mm pushrod end. As the pushrods are 1/4-28, the 10mm size was way too large to fit...

I have been having a hard time finding a thread sealer to use on the NPT fittings on the fuel tank that will withstand ethanol in gasoline. I have investigated a number of products advertised as being gasoline resistant, but none of them claimed to be ethanol resistant and based on postings on...

Hi Aaron, Can you describe a little more about how you transitioned from the stock (?) exhaust manifold into your custom pipes? Specifically, what did you use to mate from the oval flange of the stock manifold to the round downstream pipes? Did you buy a used mid-pipe/cat assembly and then...

It might, but I'm really just trying to confirm how to connect the equipment I already have (stock oil pump and Peterson dry sump tank).

Piecing together comments from different threads and using a Peterson Dry Sump tank like the 3 gallon one here Peterson Fluid Systems : Standard Oil Tanks, it looks like: 1) The crankcase breather lines #2 and #4 (See Ken's post #145 here...

Hi Peter, I have used Front Panel Express:*Front Panel Design Software and CAD Conversion Service for both instrument panels and things like trim rings. Depending on the size of the piece, they can be pretty competitive, but you can't beat the convenience of being able to design what you want...