Search results

Check Dennis at pantera performance, I have used his set up multiple times and it works great....m

I have seen your set up howard and like it. I too have an rcr set but have not installed them on the car. I am not even sure what they are rated at, which means I may just go with speedway engineering which is what I normally use..............mahlon

David it looks like a shell valley car. If you look at there site both the #27 cars as well as the #67 cars where built by me/us here in Colorado. When Rich Anderson owned shell valley years ago he purchased the molds from a company called r&d who was just doing a very basic kit. Rich had come...

Don it is nice to see your progress, those little touches sure make it cool. keep up the good work.........................m

Shell valley is still offering the Daytona coupe. It is a 90 inch wheelbase version as the originals where. They are in he process of building two right now.

Its funny you say that about the weld plates Ray, when I became a certified welder years ago on one 0f my certifications we had to do those. We would weld up all of the plates in different positions they would then cut a cross section and bend it 180 degrees, any imperfections or fractures would...

Sorry Al I just realised you where talking slc. We have not weighed ours yet...................................m

Al our RCR mk-2 comes in at 2400 lbs. I thought it was heavy, but we then looked at the full roll cage non chrome molly. Bigger brakes and wheels we run 335/35/17 on the back and they are custom american racing shelby wheels [they are heavier then some of my other race wheels]on board...

We checked this am and our hiem has been modified with an insert to allow it to thread onto the cable end....................................m

I will make it a point to check on mine tomorrow when we return to the shop and will post what I have. If it is like Dave's, I think his solution sounds solid enough for me

Nice work Dave! I will have to check mine as well, ours has been sitting on the lift and has been put on the back burner as I have not had time to get back to it...................Thanks for the info.................M

Don I have two right side fuel tanks they are the same we just checked so the right side is ok with the filler neck behind the dash and the sender at the back of the cabin near the firewall like yours. To make the left side fit as they are tapered and only go in one way it puts the sender up...

Don....I have the tilton pedal assembly in mine, and I agree that there is no room. The tiltons have adjustable pedal pads, and by adjusting the bolting positions I am able to get them on either side of the steering shaft with a little more room then the ones you have. The problem that I have is...

Aron, Shell valley classic Wheels has them in stainless steel.....

Nice work Don! I wasn't sure if you where supplied with any brackets for the mounting of the pins or not. Have you decided on which way you are going to do the outside access to the latch. I have looked at the museums and am not sure if I want to do the hole in the door that way with a lever or...

Mike I saw that as well. I think he may be the first We were in the first group to get the grazianos but our SLC has been sitting up on one of the lifts in the shop due to other projects landing on the front burners. I am hoping to get it back into the line as we are ready to wire it and have...

Thanks for all the reply's It shall be done by next week.....m

Mike we are in colorado, and have a very qualified z-f guy not to far away. The only issue is he is very busy, we thought since we are up to three of them it might be a good time to get to know one. I will probable talk to him again later this week as i need the top/bottom depending on how we...

Thanks Bob for the reply, I too have had to make tools in the past to make life easier. We will gather as much info on the process as possible before we dive in I think. I know there are a lot of knowledge out there on these and I want to do it right.We have a very qualified shop that is close...

I read a bunch of the threads I found, to find out what exactly needs to be done to flip a z-f . I could not find specific information on what exactly needs to be done. I would like to find something in written form if possible and thought about ERA as I know they have been mentioned as a source...