Search results

The mechanical parking brake was not satisfactory, I don`t think it would have passed inspection, so I followed Cam`s route and got hold of a pair of Tesla Elec parking brake calipers and a switch from Jon Haas (Pantera electronics). Made new brackets and reused the threded inserts from the old...

I added a Stewart EWP just before the radiator inlet controlled by the Holley ECU, I progammed it to come on 10* before the fans and it`s great. Before, the fans came on if I had the engine idling for 15-20 minutes, but now the EWP comes on and it takes care of the cooling. The fan stays off...

Finally got the curage to cut holes in the hood. I have been thinking of this for a year now. As a precaution I made a mold of the upper part of the front clam, just in case. Begun with the rear part of the air outlet and then the outer sides, fiberglassing it. Then did the front end of the...

I don’t have any spacers either nor the extended footbox

Great Cam, I just recieved the switch from Jon Haas and expecting the Tesla calipers within a week. Don’t think the RCR supplied parking brake setup will pass inspection here.

Hi Joel, where did get hold of this logo? I might be interested of one.

Next was fender vents. I started with the vent itself as a template and used a hacksaw to cut the vent holes. I didn`t cut all the way around, left 8 small (3-4mm) parts uncut just so the "lid"stayed in place. Then filled the holes and cutlines with clay/wax and taped the underside of the lid...

Finally got my fire supression system. It`s a water based system capable of decreasing the temperature by 1300F/700C in 10seconds. I chose manual activation. It consist of a detection loop, a plastic tube that melts at approx 330F/170C and then gives an alarm in the cockpit, then it`s up to you...

Cam, have you installed your Tesla parking brake calipers yet? If so, how wide spacer did it take to fit over the 30mm rotors? I mean spacer to widen the calipers.

In stead of the 3359 tool you can use a normal drill bit. Don’t remember if it’ 6 or 8mm

Here you go Dan, hope this will help.

Does anyone know where to get hold of a pair of new locks? Mine was delivered without. I have checked with Mazda here in Sweden, but they are like $700 for a pair.

Great solution Cam.

I can confirm it’s a great product. I have used it for shielding around exhaust tubing and the cats. On a aluminium 2mm sheet I put two layers on, and when cats are almost glowing I can touch the alu sheet. Have about 10-15mm between cat and shielding.

Yep, in Partlow, VA

Yes, the pushrods are the exact same length. I started up adjusting the pushrods so they cleared the frame rails and to same length during the alignment. However, I didn’t have the body mounted at the time, so now with the added weight I’m running out of shock adjustment. Just wondering what...

What are you Graziano/LS guys running for rear springs? As you can see I’m running 7HT850” and have to adjust them pretty much all the way up. I started with full droop and adjusted the pushrod just enough so it clears the chassi frame and went from there. The adjustment in the picture is for...

I’m using this one, no complaints. I remade my complete brake system with -3AN, got the idea from Stephan. https://www.tbmbrakes.com/product/residual-pressure-valves/

Porshe Cayenne, here you go. https://www.ebay.com/itm/05-Cayenne-S-Porsche-FRONT-REAR-Silver-INTERIOR-DOOR-HANDLES-7L5837113A-45-617/302155707407?hash=item4659e2340f:g:zMEAAOSwImRYQh39

Today`s screwup. Having spent the last 3 days for final fitment of the doors and opening mechanism I was quite happy with the result. Perfect gap all around the door and the opening/closing worked great. So when closing the door the final time I hear something falling inside the door, sounded...