Search results

Had a disaster trying to remove a spinner snapped of one of the ears on my RF, does anyone have an early RF spare Spinner they are happy to part with standard RH thread

Is any willing to share an ignition table set up for TPS load sensing not MAPS sensing for Motec (old M48). ITB's compression is 9.5.1 fuel is 98 octane Mick

Guys does anyone have a process / Methodology for front & rear wheel alignment settings for road use. Mick

Any body have the dwell settings for a Bosch MEC 726 ignition coil, googled it, called Bosch direct, called Motec no one has info. Need the correct dwell setting is everything always so hard has anybody had a tuner set one up? Mick

Any body able to take a screen shot of a Lamda table there using ?

Has anybody connected a 2 wire sensor Audi 01E to VDO electronic speedo. Recently install a new transaxle actually late model 016 has the same 2 wire sensor as the 01E. I have the wiring diagram for the VDO, it gives the option for both the 3 wire & 2 wire sensors. I have tried the suggested...

Does any one have any tips. I have managed to pick up a replacement box off Ebay in the USA, seller cant ship it but will deliver in the USA not sure how to have it shipped can anyone help. Mick

Gentlemen I'm looking for a replacement 016 5 speed anybody got one for sale?

Any one know where i can source replacement syncro's for a 016 Mick

Has anyone got any idea what would cause sudden over fueling. Have had no problem using the M48 on closed loop after dyno mapping over the last 9 months, however over the last month had to replace plugs as they have been fouling constantly ecu doesn't show any errors, change the TPS, plug leads...

Can any body shed some light on this problem. Lately the alternator warning light has been coming on and off usually happens when I first start heading out for drive after starting but can come on and off at any time and any rpm, volt meter shows no charge when the light comes on so the gauge...

Peter McCluskey's DRB & my RF at the pitstop Mt Mee north of Brizzy Sunday morning, great drive & typical Queensland winter morning perfect.

Any body able to post a motec fuel & ignition map they are hapy with for a 302 with 8 throttle bodies. I want to do some comparisons before I head of to the dyno again. PS also looking for cold start parameters Mick

Ok need some help, just installed the engine after a freshen up as a result of a blown head gasket. I replaced timing chain set reset valve timing all good, pulled down the distributor and rebuilt it didn't change any thing. Dizzy has dual hall sensor was installed in the motor before rebuild...

Need some input recently had to pull the motor to repair a head gasket leak. In the process change the pulley setup. What I have looking at the front of the motor is the alternator on Right A/C on the Left. I have all pulleys in line and can run a single V belt, im using a custom A/C bracket...

Need a bit of advice, freshening up my 302 as a result of a blown head gasket. When I pulled the motor down I notice there are 4 pistons with there valve reliefs installed on the wrong side, I don't mean upside down but with the exhaust relief on the intake side of the piston suggesting that the...

Having recently replace and upgraded the radiator, I've noticed a small amount of fluid discharge from the overflow container on the garage floor when I start in the morning. No overheating problems but not sure why it's happening. Raiditor cap is a bleed back 21 lbs. any ideas. Mick

Thought I might chime in as I have been working on installing electrically assited power steering into My RF. This is all as a result of Peter McKluskeys decrepit age an shoulder injury and my selfish need to insure he continues to be my wing man on the occasional drive into the country...

Need help guys, I have just had a 3rd aluminium radiator fail. I have used every additive plus a fitted an Interject stray current arrester. Obviously an electrical issue any suggestions on finding or sloving the problem. Not sure if a copper core radiator will eliminate the problem. How do...

Hey guys, Will land in LA on 09 September driving through to Vegas etc etc. would like to get a few travel tips if any one can help or even a beer. Mick