1. C

    FS USA SAS Pure Air 2000 Respirator System

    I have a spare, new-in-box Pure-Air 2000 Opti-Fit breathing air system that was never used. SAS Pure Air 2000 With Opti-Fit Respirators The SAS Pure Air 2000 With Opti-Fit Respirator is a unique respiratory protection system that utilizes a single air line to provide clean, filtered Grade...
  2. M

    Penski Shocks

    What pressure do you start with.. I've read 80psi minimum, 300 psi max. Nitrogen or can you use air?
  3. C

    FS USA Thermo-Tec 11710 24" X 24" Micro-Louver Air Shield

    This one is hard to find... The aluminum Micro Louver Air Shield helps block direct radiant heat while still allowing air to flow into the heat source while the vehicle is moving. The textured patterns created by the micro air louvers also create more surface area for heat dissipation. It...
  4. KENS80V

    FS USA LS engine heater core bypass valve

    I'm selling my heater core bypass set up for use with LS engines (never used). This is the Old Air Products 50-1555. I converted this control to be used by a toggle on/off switch instead of a rotary switch. Mine can also be used with no switch at all for stealth operation. You would just tap in...
  5. D

    Fuel Filling and Venting

    My car had an issue with a fuel smell in the garage and cockpit. The tank vent was a simple line that went up above the level of the tank and then down to the bottom of the frame. The smell was corrected with the addition of a valve Fuel Cell Pressure Relieving Vent Valve, In-Line, 6AN Male |...
  6. mesamaui

    FS USA New K&N low profile high performance air cleaner

    $200 incl us shipping Ca 92627
  7. D

    Another SLC hits the streets

    After 4 years of building, my SLC just received its license and registration and is now free to roam the streets. I'd like to thank everyone who posted on this forum - it was tremendously valuable during the build. Some of the details for the car include: - License plate backup camera that...
  8. C

    Thoughts on fuel tank temperature?

    I'm working on installing the fuel tank and fuel system. I had planned to install a closeout panel behind the tank, between it and the engine. I then started thinking about what kind of temperatures the tank goes through. With the engine right next to it, does the tank heat soak? Ultimately...
  9. J

    Rich and lean ....

    Hi all . another Question for you clever people .. I am running a 600 Holley and doing the final settings and I cant for the life of me remember ... is it screw the air screws in to richen the mixture and screw out to weaken ? Thanks guys John..
  10. PeteB

    A/C issues

    When the car is cold, the A/C is working correctly with low side pressure around 40 psi and vent air is 45 degrees with 85 degrees ambient air. However, after the car has been running for a while, the low side pressure is going to high (~60 psi), causing the trinary switch to disconnect the...
  11. 2

    Vintage Air Demister Vent Modification

    I'm installing a Vintage Air Mini Gen II H/C evaporator in my RCR GT40 MkI. This unit has closed off demister vents which extend higher than the three AC vents. I do not intend to use the demister vents and wonder if anyone else has cut off and capped the demister vents to prevent having to...
  12. sswartz

    RestoMod Air?

    Does anyone have any experience with RestoMod Air? Their units appear to have a lot of advantages: *Electronic controls; mode, temp, dash/defrost/heat *SPAL fan with infinite speed control *Really nice billet control options, including a single button one *Bluetooth control via iOS or Android...
  13. L

    MOAB Delivery

    Hey Fran, if I order a MOAB kit, hopefully you don't have the US Air Force deliver it to me!
  14. K

    CAV A/C Fuse

    Does anyone know the size of the A/C fuse that is under the dash in the fuse holder. Mine was replaced with a very small (that has poped) fuse after the holder fried so I would like to know what size it should be.