Search results

Hi all, A few spare parts for sale. Buyer pays shipping from Austin, TX. Everything is OBO so feel free to make an offer -- you won't offend me :) SLC parking brake kit. Removed from my SLC with about 1k miles. Includes mounting brackets/hardware for calipers and pads. Includes handle, but not...

Hi everyone Doing some garage decluttering so I have a bunch of parts I no longer need. I'm located in Austin, TX. Everything listed buyer pays shipping. Alternatively I'll be driving up to Chicago in July to move my daugher in to an apartment so can haul things up there (particularly the...

This is what I do when I can't sleep -- random internet searches :) I saw this on Hollinger's site. It appears to be a dog/sequential conversion for the Graziano. Anyone know if that's the case? If so that's pretty cool. I'm sure it's not cheap and I know dog boxes aren't for everyone :) LG6...

Hi everyone, I was just curious -- not looking for another project yet :) Has anyone tried to fit C8 headers in an SLC chassis? They *look* like they may fit -- perhaps with the primaries angled down (not up like in the c8). Bore spacing is the same as LS engines so you could just cut off the...

I think I already know the answer (don't do it) but wanted to see if anyone has done this. I need to do some additional sealing in the side areas of the body so I'm going to need to pull the spider off. Problem is the windshield is installed and I'm worried I may break it if I remove the...

Some times YouTube is way too dangerous! I want to try my hand at fabricating some parts (intake ducting, vent ducts, etc) out of wet-laid carbon fiber and was wondering if anyone had suggestions on a good place to get the basics (3K carbon cloth, epoxy resin, release agent). There are so many...

Hi guys, I've had no luck searching for the right plug for the included taillight fixture. I know it's made to fit a 2006 Dakota, but I can't find the plug that fits the bulb holder (see pic below). Anyone been able to find it? Otherwise I've found a bunch of 3157 bulb holders with wires so...

I've been eying this setup from Stance Parts: Link Curious if anyone has seen/used it. I have the Ramlift system installed already. It works fine, but it's a bit loud and slow even after repeated bleeding. From Youtube videos I've seen the air cups are much faster to raise and lower and...

These are the springs that came with my SLC kit. 2.5"ID, 7" long, 650 pounds, silver. Only used for mock up and some dyno runs. I needed to go with stiffer springs on mine. $50 for the pair plus shipping from 78732.

I have a set (with one extra) of shift cable ends (trans side). I went with spherical rod ends so not using these. Free to a good home, just pay shipping.

I have the coolant reservoir that came with my SLC kit (I ended up using a different tank). $20 plus shipping from 98052.

I bought these with my kit but have decided not to use them. I unwrapped one of them for pics, the other is still in original packing wrap. Free or a few beers for the pair plus shipping from 78732.

Original tank that came with my SLC from RCR. Perfect condition / never used or installed. $50 plus shipping from 98052.

Sold!

sold!

Hi everyone, I have a full set (4) of factory flanges. 2 are cut from ls7 manifolds just above the flange. The other two have elbows still attached with O2 bungs, cut just before the cats. I also have the cat pipes if you want them. $150 shipped within US Lower 48 for all the flanges. Add...

Hi guys, the harness that came with my kit doesn't have the column plug horn wire connected to the Infinitybox. I'm trying to figure out where I can get the right style pin to add it. Any ideas?

Tried searching the forum with no luck :( I'm wiring both fans to come on for AC and/or engine temp. I was just going to do this by running both powercell fan outputs to a single relay that in turn powers both fans. Is this a logical approach? Any better (more simple) options? Do I need to...

Where are you guys buying Tillett B5's? Tillett USA is backordered. I found a UK place that will ship pretty reasonably, but wondering if there's a better source in the USA. Thanks!

Hi guys, can someone confirm what thread pitch for Graziano starter bolts? I had read here M12x1.25, but they're not threading in. Thanks!