Awesome attention to details Chuck. Always a perfectionist.
Please keep posting !!
Regards Brian
Please keep posting !!
Regards Brian
Chuck's Jaguar D Type Build
- Thread starter CESLAW
- Start date
Bonnet, Brake Ducts
Looking at pictures of original D Types, one can find pictures with no brake ducts, rectangular shaped ducts, and oval shaped ducts. We opted for the later.
A pattern was made. Two holes were cut and joined with a saber saw. The foam edge of the fiberglass panel was sealed with a coat of epoxy.
The plan was to place the trim ring and not connect it to the opening on the font of the bonnet, but Ryan was insistent that this detail be done. Here is a picture Ryan took of an original duct which blends into the surroundings making it a detail few will notice.
A form was made to confirm the dimensions which was then used as a pattern for cutting the .030 aluminum sections. Each was made in two halves, the bend rolled, then riveted together once the fit was confirmed.
To join the tube to the front opening a plenum was needed. A half Styrofoam ball was found at our local Hobby Lobby which was modified to fit. A nipple was added to insert into the opening on the aluminum tube. Fiberglass was applied after wrapping the foam with packing tape. To remove the fiberglass from the form a bit of acetone made the Styrofoam disappear.
The inner side trim ring was cut from .050 aluminum using a hole saw and jig saw.
The trim ring was drilled for rivets, which are cosmetic. Once the fiberglass panels are painted, the tube and the trim rings will be secured.
Compare this photo with the original. Too bad few will see it once it is finished. The things we do for our kids!
IMG0260
Looking at pictures of original D Types, one can find pictures with no brake ducts, rectangular shaped ducts, and oval shaped ducts. We opted for the later.
A pattern was made. Two holes were cut and joined with a saber saw. The foam edge of the fiberglass panel was sealed with a coat of epoxy.
The plan was to place the trim ring and not connect it to the opening on the font of the bonnet, but Ryan was insistent that this detail be done. Here is a picture Ryan took of an original duct which blends into the surroundings making it a detail few will notice.
A form was made to confirm the dimensions which was then used as a pattern for cutting the .030 aluminum sections. Each was made in two halves, the bend rolled, then riveted together once the fit was confirmed.
To join the tube to the front opening a plenum was needed. A half Styrofoam ball was found at our local Hobby Lobby which was modified to fit. A nipple was added to insert into the opening on the aluminum tube. Fiberglass was applied after wrapping the foam with packing tape. To remove the fiberglass from the form a bit of acetone made the Styrofoam disappear.
The inner side trim ring was cut from .050 aluminum using a hole saw and jig saw.
The trim ring was drilled for rivets, which are cosmetic. Once the fiberglass panels are painted, the tube and the trim rings will be secured.
Compare this photo with the original. Too bad few will see it once it is finished. The things we do for our kids!
IMG0260
Very nice details !! For you, it is what we do WITH our kids. I would have loved to have my father involved. He was a strickler for details. He built RC planes with amazing detail. He would then go crash whatever he just built. He had diabetes real bad and couldn’t see so he had no idea what the plane was doing. But it never stopped him from repairing and building a new one. His glasses had trifocals in the bottom, and bifocals in the top. He would look through the slit in between. Then he wore jewelers glasses on top of them when building. Enjoy the time with your son while he wants to be involved.
My Grandkids could care less one way of the other, and I have some cool stuff. Sorry that they are being left out.
Regards Brian
My Grandkids could care less one way of the other, and I have some cool stuff. Sorry that they are being left out.
Regards Brian
All good points, well taken. I tell folks I am following in Ryan's foot steps since none of these projects would have ever been started without his input. Indeed, I consider myself very fortunate.
Battery Relocation Revisited
Back in February, 2024, relocating the battery under the seat was started. Since then, the seat brackets have been built so this detail can be finished. https://www.gt40s.com/threads/chucks-jaguar-d-type-build.52688/post-592140
The battery box was held in place with counter sunk quarter inch screws after drilling and tapping the tub floor.
A concern about the steel cross bar being close to the terminals risking a short circuit was raised, which is a good point. I found rather hefty fiberglass angle bars at McMaster Carr and decided to give it a try. It worked well, eliminating that concern.
A 1/16” rubber sheet was added to cover the front of the battery and provide additional protection from inadvertent contact.
There is a minimum of two inches clearance from the battery to the bottom of the seat.
Now I can call the battery project really done.
The next project will be removing the rear body so that the center section can be separated from the rear section, but first some spring boat, house and airplane projects need to be tackled.
Back in February, 2024, relocating the battery under the seat was started. Since then, the seat brackets have been built so this detail can be finished. https://www.gt40s.com/threads/chucks-jaguar-d-type-build.52688/post-592140
The battery box was held in place with counter sunk quarter inch screws after drilling and tapping the tub floor.
A concern about the steel cross bar being close to the terminals risking a short circuit was raised, which is a good point. I found rather hefty fiberglass angle bars at McMaster Carr and decided to give it a try. It worked well, eliminating that concern.
A 1/16” rubber sheet was added to cover the front of the battery and provide additional protection from inadvertent contact.
There is a minimum of two inches clearance from the battery to the bottom of the seat.
Now I can call the battery project really done.
The next project will be removing the rear body so that the center section can be separated from the rear section, but first some spring boat, house and airplane projects need to be tackled.
The Great Separation, Part I
After years (literally) of deliberation, the decision was made to separate the rear clip from the center body section. I was reluctant to do so, fearing it would compromise the rigidity of the body. But the challenges reaching the fuel tank and rear suspension, along with the added bit of authenticity, prompted the decision to move forward with the Great Separation.
Critical to the project was assuring that a lip could be created that would fit the rear clip precisely. We came up with a somewhat unorthodox plan.
The location of the tub’s rear panel was marked on the body. Behind the seats, the cut seam is forward of the rear tub panel. This meant that the lip would have to be wider than typical. Three inches was decided upon as an appropriate width so the lip would extend about an inch aft of the rear panel.
Fiberglass will be used to create the lip. The next challenge was coming up with a means of keeping the rear clip and the center section perfectly aligned to assure that the fiberglass would produce a lip with a good fit. We decided that the fiberglass needed to be applied before the final separation occurred.
The plan was to cut most of the seam between the two halves but leave one-inch sections in place to hold it together while the fiberglass was applied. One-sixteenth-inch holes were drilled at approximately six-inch intervals to mark the cut line so that it would be visible on the back side. The holes marked with a silver Sharpie are visible in the foregoing picture.
With the body flipped over, the drill holes were connected, marking the location of the cut line on the back side. A second line was drawn three inches aft, defining the limit of the fiberglass lip.
Once these parameters were defined, the surface where the fiberglass was to be placed was sanded with 80-grit paper until our marks began to disappear to assure a good fiberglass bond.
At this point, the body was flipped upright. One-inch widths of masking tape were placed next to each of the guide holes. The tape defined the locations where the seam would NOT be cut.
A multi-tool was used to cut along the seam between the sections of tape. It worked surprisingly well, producing a thin, straight cut.
The one-inch uncut sections will keep the front and rear aligned as the fiberglass is applied. Later, those one-inch sections will be cut with the Multi-tool. This will create a thin cut in the fiberglass lip, but that can be easily remedied. I sure hope this plan works.
After years (literally) of deliberation, the decision was made to separate the rear clip from the center body section. I was reluctant to do so, fearing it would compromise the rigidity of the body. But the challenges reaching the fuel tank and rear suspension, along with the added bit of authenticity, prompted the decision to move forward with the Great Separation.
Critical to the project was assuring that a lip could be created that would fit the rear clip precisely. We came up with a somewhat unorthodox plan.
The location of the tub’s rear panel was marked on the body. Behind the seats, the cut seam is forward of the rear tub panel. This meant that the lip would have to be wider than typical. Three inches was decided upon as an appropriate width so the lip would extend about an inch aft of the rear panel.
Fiberglass will be used to create the lip. The next challenge was coming up with a means of keeping the rear clip and the center section perfectly aligned to assure that the fiberglass would produce a lip with a good fit. We decided that the fiberglass needed to be applied before the final separation occurred.
The plan was to cut most of the seam between the two halves but leave one-inch sections in place to hold it together while the fiberglass was applied. One-sixteenth-inch holes were drilled at approximately six-inch intervals to mark the cut line so that it would be visible on the back side. The holes marked with a silver Sharpie are visible in the foregoing picture.
With the body flipped over, the drill holes were connected, marking the location of the cut line on the back side. A second line was drawn three inches aft, defining the limit of the fiberglass lip.
Once these parameters were defined, the surface where the fiberglass was to be placed was sanded with 80-grit paper until our marks began to disappear to assure a good fiberglass bond.
At this point, the body was flipped upright. One-inch widths of masking tape were placed next to each of the guide holes. The tape defined the locations where the seam would NOT be cut.
A multi-tool was used to cut along the seam between the sections of tape. It worked surprisingly well, producing a thin, straight cut.
The one-inch uncut sections will keep the front and rear aligned as the fiberglass is applied. Later, those one-inch sections will be cut with the Multi-tool. This will create a thin cut in the fiberglass lip, but that can be easily remedied. I sure hope this plan works.
Doug M
Supporter
Territory that I’m too scared to venture into, but I have full confidence in your build skills and I’m looking forward to seeing your process.
I have the same concerns in regard to maintenance, but so far I think I have devised a way to make a lot of the rear end accessible via removing the rear wheels and having the inner fender panels attached with Rivnuts or bolts for reasonably easier removal. Also, the updated fuel tank supports can be unbolted and lowered in a worse case scenario.
I have the same concerns in regard to maintenance, but so far I think I have devised a way to make a lot of the rear end accessible via removing the rear wheels and having the inner fender panels attached with Rivnuts or bolts for reasonably easier removal. Also, the updated fuel tank supports can be unbolted and lowered in a worse case scenario.
Good point. If someone did a cost / benefit analysis this project would get cut from the list. Your approach will provide access to virtually everything one would ever need to access. Indeed, getting into the project, it is apparent that some additional bracing will be needed to make up for the rigidity lost when the rear clip is separated.
But I am having fun with this project, and after all it is a hobby, so we will see how it ends up. Hope to post some more progress updates shortly.
Doug M
Supporter
Fun is the name of the game. And I would imagine that if it ultimately proves too impractical to have the boot/butt of the car on a hinge type setup like the original, it can be mounted on a sub-frame so it can just be detached and removed completely should the need arise.
You raise a good point. I have never seen an original D with the rear clip opened up as if hinged. I am fairly certain that it was designed to be removable, not opened up on a "hinge". Most had their exhaust under the body and the exhaust system would have to be removed to afford clearance when opened on the "hinge." Add to that the rubber fuel cells and the fuel filler complicating a hinged arrangement.
Regardless, my plan is to make the rear clip easily removable by loosening two nuts inside the 'trunk' and a quarter turn of the fasteners on the leading edge. It will also be possible to open as if hinged, but that is not the primary goal. Whether this all works out as planned remains to be seen.
If anyone has seen a picture of an original with the rear clip opened up as if hinged I would love to see it.
Pedro
Supporter
I could be wrong of course but these look like flat head screws to me, some really nice pictures on this site below.
Attachments
Yes indeed, those do look like screws. Other pics show larger head Dzus style fasterners, which is what will likely go on our D Type.
Pedro
Supporter
Just wondering if these are pivot points for the rear bodywork? Apologies for hijacking your thread
https://www.broadarrowauctions.com/vehicles/am25_r086/1954-jaguar-d-type-okv-2-works-competition
https://www.dkeng.co.uk/restorations/102/Previously_Restored_Cars/jaguar_d_type.html
https://www.broadarrowauctions.com/vehicles/am25_r086/1954-jaguar-d-type-okv-2-works-competition
https://www.dkeng.co.uk/restorations/102/Previously_Restored_Cars/jaguar_d_type.html
Attachments
No apology needed! Yes indeed, those are the rear supports for the clip. Those two joints carry much of the weight.
Thanks for adding those links. Some very good pics for future reference.
The Great Separation, Part II
The next part of the project was wiping down the surfaces where fiberglass would be applied and then taping off the aft section to prevent the fiberglass from adhering. Shiny packing tape was carefully inserted into each of the cuts, wrapping it both top and bottom, since the fiberglass resin could seep into the cut line.
The body was flipped over, and both packing tape and duct tape were applied on the underside aft of the cut line to prevent the fiberglass from adhering.
The fiberglass will be applied up to the black line marked on the duct tape, three inches aft of the cut line. Once the tape was smoothed as well as possible, it was waxed to ensure the fiberglass lip would release.
Next, we set up to install the fiberglass, a project which will be tackled later.
The next part of the project was wiping down the surfaces where fiberglass would be applied and then taping off the aft section to prevent the fiberglass from adhering. Shiny packing tape was carefully inserted into each of the cuts, wrapping it both top and bottom, since the fiberglass resin could seep into the cut line.
The body was flipped over, and both packing tape and duct tape were applied on the underside aft of the cut line to prevent the fiberglass from adhering.
The fiberglass will be applied up to the black line marked on the duct tape, three inches aft of the cut line. Once the tape was smoothed as well as possible, it was waxed to ensure the fiberglass lip would release.
Next, we set up to install the fiberglass, a project which will be tackled later.
Doug M
Supporter
Chuck, it might be the Mandela effect, but I haven’t really seen a picture of the back section on a hinge, either, though I feel like I have. My thoughts are that it all has to rest on something, so I could see the rear section tipping back and then lifting up for complete removal.
Update as I’m writing this… I did some more digging in my research books and online. I found an Instagram account of the restoration of XKD 522. There are some internal details shown about the rear end, including these pictures that show a hinge setup, but I’m fairly certain I’m correct that its supposed to be unbolted from the mid section, then tipped back and removed.
Update as I’m writing this… I did some more digging in my research books and online. I found an Instagram account of the restoration of XKD 522. There are some internal details shown about the rear end, including these pictures that show a hinge setup, but I’m fairly certain I’m correct that its supposed to be unbolted from the mid section, then tipped back and removed.
Very interesting picture. It actually confirms it was not intended to be opened on "hinges" but rather removed.
Missing in the picture is the rest of the underbody brace. There is another section that extends aft from the brace shown in that photo, visible in the picture posted by Pedro. We have been assuming that the clip was supported only by the aft connection points on that underbody brace. The picture you posted reveals it was supported not only by the aft connection point, but also by a connection forward of the trunk, near the rear tires. With four connection points to the underbody frame it would be impossible to open it as if hinged at the rear.
Removal of the rear clip would require disconnecting the four bolts securing it to the under body frame, removing the wide head screws around the leading edge of the body, removing the under body connections to the exhaust, and removing the screws holding the body to the drip pan around the fuel filler. It could then be lifted off.
The rear clip was clearly designed to be removed, but doing so would have been a big job.
I have seen pictures of the rear clip sitting by itself, but non with it in a "hinged" open position.
Those are good pics I had not seen before. Thanks for posting.
Missing in the picture is the rest of the underbody brace. There is another section that extends aft from the brace shown in that photo, visible in the picture posted by Pedro. We have been assuming that the clip was supported only by the aft connection points on that underbody brace. The picture you posted reveals it was supported not only by the aft connection point, but also by a connection forward of the trunk, near the rear tires. With four connection points to the underbody frame it would be impossible to open it as if hinged at the rear.
Removal of the rear clip would require disconnecting the four bolts securing it to the under body frame, removing the wide head screws around the leading edge of the body, removing the under body connections to the exhaust, and removing the screws holding the body to the drip pan around the fuel filler. It could then be lifted off.
The rear clip was clearly designed to be removed, but doing so would have been a big job.
I have seen pictures of the rear clip sitting by itself, but non with it in a "hinged" open position.
Those are good pics I had not seen before. Thanks for posting.
