Search results

I have for 16 years run my 4150 double pumper carb backwards on a Edelbrock RPM Airgap Performer intake manifold. It’s simply easier to run the throttle cable instead of fabricating a bell crank. I have never been satisfied with the idle quality and wonder if this might be the problem. Opinions...

I recently converted my 016 Audi transaxle to a 01E in my Roaring Forties GT40. Offering my complete 016 adaptor kit $500 buyer pays freight. Located in North Carolina USA.

I’m changing the gearbox in my RF #103 from Audi 016 to a 01E and need assistance. The the 016 cv joints are 930 type with OD 108mm and I would like to continue using this setup. The 016 output shafts will interchange to the 01E which would allow this, however I hope someone has performed this...

Rebuilding my 016 Transaxle and need new pinion bearings, located in North Carolina, USA.

I am in need of a new steering rack for my 2005 Roaring Forties #103 LHD. Anyone have info about which car this rack was originally fitted or a possible source. Thanks, Jim

All of my soft suspension bushings have exploded! I cant seem to find a source. Has anyone had this problem? The bushings are crumbling apart sitting in my shop and I don't have the means to machine a set. HELP

I would like to add a rear swaybar to RF #103. If anyone has source info please advise. Thanks,

I have a defective new (3k miles) radiator. I need repair or replacement and would like advise for possibilities in US before calling Roaring Forties for a replacement. Thanks in advance!!

I have 2 circlips left from my build. Is anyone familiar with where they belong. They look like retaining clips for a u-joint, but I haven't a clue where I omitted them. Thanks,

I need 5 wheel studs (so you guessed what happened) for the rear hub of an RF. I can't find replacements without knowing the car application. If anyone has a local solution (US) it would be appreciated.

I can't find a source in the US to purchase sleeved grommets as supplied by RF used to pass cables etc. through panels . I would appreciate a little help (source). Thanks All

I need ideas for location of interior door light switches. I see several possible locations and would like to see what you guys have done. I can't find a thread on this item. Thanks in advance!

I need a similar to original inside mirror. I am curious as to what types are being used and if anyone has a spare for sale. Thanks, Jim

I need a photo of the later style rear muffler supports that bolt to the rear of the transmission. I have been looking at my brackets for several evenings and I am certain they must be manfactured wrong. I've finally realized the puzzle cannot be solved by me! Pics Please!!!!!!!!!

I need high quality (max scratch resistant)side windows for my RF with pop out panels(square). Whose windows will interchange? Thanks Jim

I have noticed on the forum many engines don't have this coolant bypass configuration. RF supplies this injection manifold with these holes predrilled to eliminate steam pockets. I am using a 4 barrel carb and noticed from the gallery many cars don't seem to need the modification and I don't...

I have no clue as to where to source a crankshaft pulley for a "0" balancer (3 or 4 bolt) on the standard RF belt system and thought someone may have already found the answer. Thanks in advance, Jim

Does anyone have recomendations for spigot bearing lubricant (RF Needle type)? I also need recomendations for release bearing (thrust bearing) sleeve (Nose) lube. Any wisdom would be greatly appreciated! Jim

I can't decide where to mount my msd box. I was going to mount it in the engine compartment on the right bulkhead panel but concerned about heat. Any recomendations (carb. engine) Thanks, Jim

I'm interested in photos (ideas) of wiring exit (hole) location in the front bulkhead servicing the fans,front clip, etc.. The harness is a halfbreed and the brake system is in the location of the hole detailed in the build manual. I bet there are some creative ideas about locating it without...