Search results

2013 Boxster and 2014 Cayman use PDK

I am using C5 suspension on my project front and rear so if there are any dimensions that you need let me know

Are the parts coated with some kind of corrosion coating? it seem strange to do that much assembly before applying a Zinc chromate or alodine conversion coating. all the aluminum I have used in aircraft have been coated before assembly to prevent corrosion between the parts

I see Mercruiser and Ricardo but what chassis. any one know a little about it

the clutch does not have as high a pressure as the brakes. you could run braided all the way. the clutch slippage is caused by to small a line. with a small line there is a lag time from when you let the clutch out untill the pressure bleeds of on the slave cylinder. on a hard launch the clutch...

The inside is the least likely to be affected by corrosion it takes Oxygen to corrode stainless. the glycol keeps the oxygen from the surface of the tube. the outside is the most susceptable to corrosion even more if insulated. insulated stainless pipe should be cleaned and primed before...

I was just look at some of your pics of the project and this is a great project keep up the good work. the picture of the cooling system pipes show some color near and around the welds it looks like you cleaned the welds with a wire brush or wire wheel or maybe not cleaned at all. in either...

if it is 304 I am suprized it rusted. did you use fill rod om the welds? there are passavation processes that you can do your self using citric acid, it takes a little long but is is safe to do at home and Green. 10% citric acid in disstilled water for 30 minutes at 150 degree F...

don"t panic, some stainless is magnetic. the high chrome/ nickel 300 series alloys are mostly not magnetic but a few alloys are slightly magnatic. some of the car parts makers use 409 stainless and it is magnetic, not as corrosion resistant a the 300 series but ok for cooling lines . mostly used...

Ijust found this so it looks like that is not it Starter Terminal Wiring Kit Ford F250SD 05 - 08 09 10 : eBay Motors (item 230462697620 end time Sep-12-10 13:07:22 PDT)

I found it on the online parts site. $7.74 sounds to cheap to be what we are looking for. https://www.silverstatefordparts.com/oem-Ford-parts.html when I buy for parts I almost always buy from Silver State Ford online. if it is listed then they will ship it. they always have the best prices of...

I have a small lead on the pigtail part #. there is a service part # for some ford starter terminal problems and a replacement connector pigtail that matches the Ford basic part number with the number in the Ford GT wiring book 14A280 just don't know what the basic number means. is it the...

there is no seperate starter solenoid in the ford GT. the battery wire goes directly from the battery to the starter and the alternator output wire is also connected to the starter terminal. for the small connector I used a 3/16" wide spade connector and filled it with silicone leaving a 6" pig...

Single man Cats are a lot of fun but with only a main sail they do not have the speed of a Cat with two or three sails.They benefit by the accelerated air between the main and jib sails. single sailed Cats come about very slow and are very hard to sail in a light wind. The F18 cat is my favorite...

they just wanted a bundle of snakes, but they did not have room under the hood so they put them on top of the hood. I guess that's a resonable idea?

why clean it? we should think green here. if we clean it up there would be a lot of toxic waste and pieces of Sh*t to dispose of . why not make the container of biodegradable material and just compact it, then store it in a very deep hole in the ground somewhere in the world where it is more...

How much HP are you running? 600 Lbs/hr maybe. 600 Gph would be good for 4000 HP the A1000 is good up to 1500 HP still a bit over kill for a GT 40. the A 1000 is to big and unless you are running -10 suction lines you may be cavitating the suction of the pump which will shorten the pumps life...

That is the same as the KERS system that was used in F1 last year. very cool stuff YouTube - F1 KERS system 2009

if you could find one they run about $500 for NOS I have seen a few in the last 6 months heres one used vintage stewart warner 240a 240 a fuel pump electric sw: eBay Motors (item 220641865576 end time Aug-01-10 18:00:00 PDT)

the tank in a pressureized line will not improve the flow. no more fuel will flow out of the tank unless you let either air into the tank or more fuel. you will only get out the same amount that can get in. how is a surge of fuel going to get out if you do not let the same amount of surge get...