Search results for query: Q PLATE

There are two SKF 320/28 X/Q (52mm OD, 27.80 mm ID, 11.90mm wide outer race, 16.54mm total width ) tapered bearings and one SL 183005AXL-INA (47mm OD, 25.90mm ID, 15.94mm wide) roller bearing. Shaft comes with the Renault type 24mm/21 spline which fits Esprit clutch driven plate. As an...

...donor vehicles components? So I assume If I use all new components, i'll get a new registration and if age can't be determined i'll get a Q plate? For age-related registration I need to use two from suspension (front and back), Axles (both), Transmission, Steering Assembly or Engine in the...

...better. The early cars are OK if all you want is something that looks like a GT40 but the chassis are pretty poor. The KVA bodies are OK. The Q plate is a bit of a kiss of death as it will trash the value of the car. A GT40 on a Q plate will be quite hard to sell. The Rover engine also won't...

<table border='0' cellpadding='8'> <tr><td> <a href= 'http://rover.ebay.com/rover/1/710-53481-19255-0/1?ff3=2&toolid=10039&campid=5336885271&item=131993051680&vectorid=229508&lgeo=1' target='_blank'><img src='http://thumbs1.ebaystatic.com/m/mhsW_oUgg_k-zFM0JSwdDFQ/140.jpg'...

As previously mentioned it’s been advertised for months and must be a bargain now as it’s been reduced by £5k. At least they’ve now pulled it out of the corner of the showroom for some decent photos! I’d compare the asking price to what you’d get (with receipts needed to claim a new build) from...

I have the 6 point harness but in a DRB. The floor is much different and of no help to you. If you google 6point harness mounting there is a listing for "Images of the 6 point harness mounting" and every possible configuration of use. On my computer it is...

...that you have not used any old parts. You are allowed one reconditioned part (normally the engine) and have to demonstrate that it has been rebuilt to an as new standard. If any of this is in doubt then DVLA will assign a Q plate and then you will not be able to use a private plate on it. Brett

...for the springs/dampers. It's not a particularly pretty chassis on those early cars. Rover V8 on Renault gearbox. Registered on a Q plate. It's been completed and used on the road, but has been lying unused for a while. It would take a real good going over to get it properly...

...on already. GT40 is my dream though, so I could cruise around in it for a while, then rebuild it into something special. To remove the Q plate is a massive issue, so ultimately that's a problem. Not sure if e marked glass is available for them and it would be a very difficult thing to IVA...

Sheesh - I can't even enter my own email address correctly in the original post. It is : [email protected] Below is an image of the styles I have available. I can make any custom plate as well but obviously I need to generate artwork. As to Mike Drew's suggestion about the history of...

Hi Russell, sorry must have missed this Q, don't see much of a problem with that but would suggest that you consider an external pickup from pan to pump plus some horizontal tubes in the pan to prevent oil surge from front to rear & vice versa. The OE pickup drilling in the block has caused a...

...it over the next 4/5 yrs I'm very good with cars so the build shouldn't be to bad (hopefully) one thing I'm not quite sure of is the Q plate as I'm wanting to build this on a budget while not compromising the quality of the build if any used parts are used i take it Q plate is the only...

David think of Keiths bones, you would be better off getting one of these road going couches. Bob

...back in early 1990 would have been about £20000 plus VAT But without proof of purchase of the Chassis as new etc you will end up with a Q plate at registration and that makes the finished car less desirable (Dax / DJ Sprotscars in Essex may assist with copies) From that stage to complee...

Hi Just seen a discussion on the locostbuilders site about using black & silver plates on a q reg. Apparently VOSA have confirmed that it is fine to do so from an MOT point of view. Useful for anyone with a q-plate wanting more of a period look. Yet another Q plate question

I wonder how long it will take to accumulate 7,500 paid applications. If I read the DMV site correctly (Q&A) it'll take 9-12 months after implementation to receive Legacy plate. No real incentive to send in $50 prepayment. Might as well wait to see if it gets implemented at all. Then again if...

So here's the brakes. First one is bare upright with small notch relieved in bottom of caliper mount location. This is necessary if you do this. Not a big deal but you will need a high speed air tool and a cutting tool. Run at about a 25% full speed or you will burn up the tool. Take it easy...

You nailed it. It's another example of the government’s inability to take a simple great idea and create a clumsy policy and an unnecessary potential quagmire. That said I'm still very much in favor of the goal. There's likely a myriad of small trick things one can do to embellish their GT40...

here is what I have found: Registering a Vehicle in Ontario About “Street Rods / Hot Rods” The Ministry of Transportation (MTO) does not have any specific registration requirements for Street Rods under the Highway Traffic Act. Furthermore, we do not have any legal definition of either "street...

Hi guys A quick question for those in the uk that have registered their cars avoiding a Q plate. I know you have to provide receipts to show that major components are new but do they have to be just from manufacturer/supplier? What about buying something from an individual who bought the...