Classic HorsePower Scratch GT40

[Devin]

How did the dash fit that I sold you?

David, as with everything…I made it fit! It took a bit of trimming as I wanted to expose the lower structure of the dash support metalwork replicating the original race cars. I couldn’t have gotten this far without the parts I got from you and this forum!

 

[Devin]

Ended up spending an hour today hanging motivational art around the workshop and mancave. Sometimes you just have to take time to “smell the roses”.

 

[Davidmgbv8]

David, as with everything…I made it fit! It took a bit of trimming as I wanted to expose the lower structure of the dash support metalwork replicating the original race cars. I couldn’t have gotten this far without the parts I got from you and this forum!
View attachment 153229

Looks good, like the exposed metal bits

 

[Devin]

Started wet sanding the rear clam today. I knew this was a curvy dame but once you start having to sand every inch, you realize that there isn’t very many flat areas to use a sanding board on.

 

[Devin]

This weekend’s work was on the rear clam latch pockets as well as placing the front & rear clam bumpers to set the clam height and lower panel gaps. Next I’ll mix a batch of epoxy resin & colloidal powder for fastening the backing plate to the pocket opening.

 

[Mark H.]

Looks like you are using a Porsche shifter box?

 

[Devin]

Looks like you are using a Porsche shifter box?

Yes sir, Boxster S transaxle, cables, shifter and inner CVs.

 

[Mark H.]

I thought it looked familiar. I have a V-8 Lotus Europa project with a G86 transaxle and used the stock shifter box and cables too, but upgraded with a shorter throw shifter kit which was a big improvement. Just a comment.

 

[Alan]

This weekend’s work was on the rear clam latch pockets as well as placing the front & rear clam bumpers to set the clam height and lower panel gaps. Next I’ll mix a batch of epoxy resin & colloidal powder for fastening the backing plate to the pocket opening.
View attachment 153445
View attachment 153446
View attachment 153447

Hi Devin what latch are you using?

 

[Devin]

Hi Devin what latch are you using?

Replica Hartwell…if I would have know they weren’t adjustable like actual Hartwells, I would have gone with another choice. They look ok but the quality isn’t what I expected for what I paid. PM me if you want more details.

 

[Devin]

Latch mock-up after epoxy resin dried. Some sanding and fiber filler around the backside should finish these pockets up nicely. Believe I will wait until final paint to drill and mount the upper latch in place.

 

[Devin]

Quick evening project…conversion/upgraded short throw shifter from the stock plastic Porsche stick shifter. Spent too much time trying to gently convince the old plastic retainer/bearings to come out last night…went with the more expedient YouTube way of cutting the plastic retainer clips and quickly liberating the shifter. After a quick trial fit and small modification to the recommended installation and lubing all friction points, it installed in minutes and works great. The feel is so much more precise and will look better through the future bespoke open shift gate (to replicate the original types).

 

[Devin]

Finished up my rear clam hinge and limit cables. Due to my “easy to remove” hinge pivot design, I needed to make a quick latch to keep the rear pivot support bar from inadvertently slipping out of the hinge beak when opening it to the vertical position. I wanted to keep with my aviation/racing heritage, so I utilized a pair of quick release safety pins to lock the latch into position. Once over center, I installed a pair of limit cables (12”) that are tethered to the clamshell rear tail support fiberglass structure. It worked out great to keep the clam nearly full vertical but yet keep the tail a good distance from any potential curb or parking spot concrete barrier (~5” clearance).

 

[joe]

I’m thinking about using a prop rod like Ford used on my late Mustang hoods, instead of cables. I’m a little concerned about a gust of wind blowing it shut.

 

[Devin]

I’m thinking about using a prop rod like Ford used on my late Mustang hoods, instead of cables. I’m a little concerned about a gust of wind blowing it shut.

Yea was thinking that I would carry an adjustable/folding prop just for shows and extended times it would be open. Mine is fairly heavy once over center so needed a positive heavy duty stop for any time I open it.