Injection stack covers?
- Thread starter Twosheds
- Start date
Glenn M
Supporter
Yes! They are readily available, especially after Wimbledon!
(And can even be custom made)Attachments
Yes! They are readily available, especially after Wimbledon!
"Great minds think alike" as my dad used to say, although he sometimes added "fools seldom differ" on the end
, just the job I was doing today. Although my trumpets not being as big as yours, meant I had to drill holes in my balls to get them to fit, so they don't line up as nicely as yours do 
Bill Kearley
Supporter
On the Ball as always Glenn, you beat me to it, my balls are green by the way.Yes! They are readily available, especially after Wimbledon!
Ian Anderson
Lifetime Supporter
I saw a set once for Webers that was made out of Branston pickle jar lids (No Branding thereon)
Nicely chained together and snug fit over the trumpets. Being that small they were carried in the door pocket.
Ian
Nicely chained together and snug fit over the trumpets. Being that small they were carried in the door pocket.
Ian
Eric B
Eric
Bill, is that a heat shield you constructed between the headers and the injection? I may have to address that on my build currently in progress.
Who made the headers? They are purdy!
E
Bill Kearley
Supporter
Yup, a piece of alu with a bend that goes down close to the engine block and a piece of flat bar welded on and bolted to the intake manifold.
The headers are from GP Headers in Minnesota 218 493 4251
The headers are from GP Headers in Minnesota 218 493 4251
Thanks for the reply, but I'm not looking for air cleaners. I have a set like Bill's.
I'm looking for covers that are put on when the engine's not running like over the winter or at a car show.
Bill Kearley
Supporter
You run without air filters? If so a coverup for storage could be quite creative like Enzo bobble heads.
Neal
Lifetime Supporter
EMPI makes rubber IDA covers.
C13-43-5721 - EMPI BRAND - MOLDED VINYL VELOCITY STACK COVERS - FIT 48 IDA WEBER CARB.(NOT PRO-STACKS) - PAIR
C13-43-5721 - EMPI BRAND - MOLDED VINYL VELOCITY STACK COVERS - FIT 48 IDA WEBER CARB.(NOT PRO-STACKS) - PAIR
www2.cip1.com
Those look like the ones that I had for Webers.EMPI makes rubber IDA covers.
C13-43-5721 - EMPI BRAND - MOLDED VINYL VELOCITY STACK COVERS - FIT 48 IDA WEBER CARB.(NOT PRO-STACKS) - PAIR
C13-43-5721 - EMPI BRAND - MOLDED VINYL VELOCITY STACK COVERS - FIT 48 IDA WEBER CARB.(NOT PRO-STACKS) - PAIRwww2.cip1.com
I looked over the web site and they had some slightly larger ones. I ordered a set and will report back on their fit (or not).
Doug
Or you go to the hardware and buy sink plugs and some cord to link them together.
Jim
Jim
If it is the Bill B I dealt with a few years ago, he was in Texas and made the filter covers for me that are in this picture. There is a coarse filter and fine filter that appear to work pretty good. They could be ordered with different filtration screens and I went with the finest mesh possible
Attachments
Doc Watson
Lifetime Supporter
it was only 12 years ago.....
#57 for mine
individual Weber screens
Can any of you explain (in simple language, please!) the effect of the taper and length of the trumpet - I think I've been told that a longer trumpet will yield more torque, although if this is the case there's presumably a trade-off. I'm just wondering what the downside of a pronounced taper...
www.gt40s.com
#57 for mine
Attachments
Bill Kearley
Supporter
A while back it was Bill D. sitting on a side walk. I watched his build. I enjoy'd that one.
Last edited:
Bill Kearley
Supporter
